Output Voltage("H"):[(Supply Voltage) -2.5 V] or more
Output Voltage("L"):0.4 V or lower
Output Current(Sink "L"):Up to 30 mA
Output Current(Source "H"):Up to 10 mA
KOYO Compact Universal Incremental Rotary Encoder TRD-J400-RZL
People who bought this item also viewed
Tamagawa Seiki Encoder TS5667N253
HENGSTLER Encoder RI41-O/500ES.11KB
Nemicon Encoder HEF-2048-2MHC
Yaskawa Servo Motor SGM7G-30A7C61
Panasonic Servo Drive MEDLT83SG
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
NORGREN Air Cylinder RM/92032/M/110
Vickers Solenoid Valve DG4S4LW-012B-B-60
Balluff Sensor BOS01MP
Recent related posts
-
01/08/2021
Four major producing areas of Mitsubishi Electric's central air conditioner
Four major producing areas of Mitsubishi Electric's central air conditioner Four-major-producing-areas-of-mitsubishi-electric's-central-air-conditioner Wakayama, Japan Founded in 1943, the cold and heat system manufacturing plant entered the open r 器2 䀀 ᅵ皥 䖒皦즠Ʋ奌ི 㲈Ʋ 䌁皦 ᮔDž༬皧奖ིЀ 呄ᠾ鹨់༹皧 ࠄ 00령ꐱ댁珵뛐珵Љ 䕄ྦ 뤂ᐱ뚜珵 ᴴᏩ呄ᠾ퍘ᒥ 鹨់ᩄ ꋔྦ 瑉浥 巠皱㙲皦抐皱 巠皱 ੨皦柘皱 ᅵ皥 ب 巠皱㙲皦忈皱 ੨皦柘皱 즠Ʋǜ 勁皦즠Ʋب ǜ V / 펔B䌁皦 ᮔDž '鱤džၜ먢䇨珵呈ᠾ뤂ᐱ ⿇⬿먲僧ᐱ㥲ᐲ�僬㣢ᐲ ᠾ 랖僧Ԃ 識 �僬㣢ᐲ 臆S㥲ᐲ ᬄğ 識 理艏S杴 識杴 㥲ᐲ
-
07/30/2020
FAQs on refrigeration compressors, do you know these
Impurities entering the friction surface of the moving parts of the compressor pump body will cause abnormal scratches and wear. Impurities entering the solenoid valve, expansion valve, control valve, capillary tube and stop valve in the refrigerator system will block the valve hole or The valve is not closed tightly and fails.
-
09/11/2020
Provide compressed air without oil, water and dust
The drying effect is achieved through the principle of pressure swing adsorption. Not only can it be matched with a small air compressor, but it can also meet the needs of local users with special requirements behind the large air compressor, so as to avoid the high air quality requirements of individual points and the high configuration of the entire equipment to save investment.
-
06/14/2020
How to repair the air conditioner compressor failure
Pharmaceutical freeze dryer composition system introduction The freeze dryer is also called freeze dryer and vacuum freeze dryer. The pharmaceutical freeze dryer is divided into common type and gland type. Its system software is composed of refrigeration 器2 䀀 ᅵ皥 䖒皦즠Ʋ煔क़ 㲈Ʋ 䌁皦 ᮔDž༬皧煞क़Ѐ 呄ᠾ鹨់༹皧 ࠄ 00령ꐱ댁珵뛐珵Љ 䕄ྦ 뤂ᐱ뚜珵 ᴴᏩ呄ᠾ퍘ᒥ 鹨់ᩄ ꋔྦ 瑉浥 巠皱㙲皦抐皱 巠皱 ੨皦柘皱 ᅵ皥 ب 巠皱㙲皦忈皱 ੨皦柘皱
-
09/07/2021
How to Test a Mass Flow Sensor?
The mass flow sensor, or air flow sensor is one of the important sensors of the electronic fuel injection engine.
-
03/21/2022
How to Select Linear Guideways?
Whether we use linear guideways in 3D printers, automatic dispensing machines, automatic screen printing machines, CNC machine tools, CNC machining centers
-
04/11/2023
How to Replace Refrigerator Compressor
A compressor is a machine that compresses gas and increases the pressure of the gas at the same time. It is widely used, and common application fields include: HVAC, refrigeration cycle
-
09/06/2020
What effect does the high oil mist content in the compressed air have on the operation of the refrigeration dryer
The exhaust oil content of air compressors is different. For example, the exhaust oil content of domestic piston type oil-lubricated air compressors is 65-220mg/m3, and the exhaust oil content of low-oil lubricated air compressors is 30-40mg/ m3, the domestic so-called oil-free air
-
07/23/2020
Analysis of Overheating Failure of Refrigeration Compressor
The main reasons for the overheating of exhaust temperature are as follows: high return air temperature, large heating capacity of the motor, high compression ratio, high condensation pressure, and improper refrigerant selection.<br></br> <br></br>
-
01/04/2024
3D Printer: Working Principle, Function of Components and Solutions to Overheating Problem
3D printing technology emerged in the mid-1990s. Its basic working principle is similar to regular printing. The printer contains powdered materials such as metal or plastic, which can be bonded together.