EATON HMI XV-232-57BAS-1-10
People who bought this item also viewed
Weintek HMI MT8070IE
Siemens HMI 6AV6 652-4GC01-2AA0
Mitsubishi HMI F930GOT-BWD-E
Cermate HMI PL035-TST1A-F1
Yaskawa Servo Motor SGMP-02AXSWX
Sanyo Denki Servo Drive PZ0A100HF86S0N
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
Yaskawa Servo Drive SGDH-08AE-S-Y905
AVX Capacitor 35V 6.8UF
SMC Solenoid Valve VQD1151W-5L
Honeywell Sensor CSNS300M-002S
Recent related posts
-
07/01/2020
Analysis of the main advantages of Copeland compressors
Analysis of the main advantages of Copeland compressors Copeland compressors not only have a high reputation, but also stand out among well-known brands. It is precisely because Copeland compressors have the advantages that most compressors have or do not have.
-
09/02/2020
There are 8 reasons for the high fuel consumption of air compressors, some of which can't be thought of!
Run oil In our daily work, we often encounter the problem of air compressor running oil. In addition to the quality of the oil itself, what other reasons can cause the running oil? In practice, engineers have summed up several reasons that can cause oil running. Let's share with you.
-
06/19/2020
What are the causes of air conditioning trip
What are the causes of air conditioning trip 1. The contradiction between the rated current of the air conditioner and the current carrying capacity of the wire. Here are two formulas involved: ①The rated current of air conditioner I=P÷U ÷power factor, the power remains unchanged, the smaller the voltage, the greater the current required. ② The current carrying capacity of the wire I=U÷R, the voltage is proportional to the current. So when the power supply voltage is normal, we must consider the line voltage drop. The longer the line, the greater the resistance, the greater the voltage drop, and the smaller the output current at the end. However, because the power of the load remains unchanged, the voltage becomes smaller, and the current that needs to be output will be larger. At this time, the wire is forced to overload, and the time will cause heating, and eventually cause the tripping of the open circuit. Some friends said that the heat of the wire will not cause the tripping of the circuit breaker. In fact, the manufacturer of the air switch has made it clear in the relevant manuals that the heat of the wire will cause the air switch to trip. Because the wire heats up, the crimp terminal will also heat up, and the resistance will become larger and larger. The larger the resistance, the greater the current consumption, and the hotter it will be, a vicious cycle. 2. Leakage During the daily maintenance work, we will encounter the situation that the air circuit trips due to the leakage of electricity. At least I have not experienced it once or twice. Regardless of the leakage of the neutral line or the leakage of the live line, a long time will cause the circuit breaker to trip. Why does the electric leakage cause the MCB to trip? There are two situations. ① Good grounding. At the beginning, the leakage current was not large, and as time went by, the leakage current became larger and larger, and eventually evolved into a short circuit to ground, unable to close. ②There is no ground wire. If the equipment is not connected to the protective ground, when the wire leaks to the equipment, it is equivalent to adding a large shunt resistance. Like this problem, if the air conditioner does not have a ground wire, when the wire leaks to the air conditioner, the air conditioner is a very large shunt resistor and will consume a lot of current. Eventually, the wire will heat up or trip open. How to determine whether the trip caused by the above two aspects can be done with a clamp ammeter. ① Measure the voltage at the input and output to see if there is a significant change in voltage drop. ②Measure whether the output current exceeds the standard. So my suggestion is: first measure the supply voltage to see if it is within the allowable fluctuation range. Then measure the current to see if it exceeds the rated ampacity of the wire. Finally, check the data one by one according to the measured data to find out the reason.
-
08/19/2020
How to dehumidify the refrigeration system of industrial refrigerators
The water content in the industrial refrigerator system comes from two aspects. One is that the vacuum is not in place, so that air and water vapor remain in the system. The other is that the
-
08/22/2022
Speed-Torque Curve of Stepper Motors and FAQs
This is the torque the motor will produce when the motor is stationary and rated current is applied to the windings.
-
05/08/2022
How to Clean Automobile Solenoid Valve?
Before removing the valve body from the bottom of the transmission, take extra care when removing the flat wire of the external solenoid valve.
-
06/13/2020
Is there any problem with compressor oil return
Is there any problem with compressor oil return 1. Mechanism analysis of compressor oil shortage During the operation of the system, the lubricating oil is discharged from the compressor along with the refrigerant, and then returned to the compressor 器2 䀀 ᅵ皥 䖒皦즠Ʋ焬क़ 㲈Ʋ 䌁皦 ᮔDž༬皧然क़Ѐ 呄ᠾ鹨់༹皧 ࠄ 00령ꐱ댁珵뛐珵Љ 䕄ྦ 뤂ᐱ
-
06/13/2020
Refrigeration compressors can be divided into two types
Refrigeration compressors can be divided into two types: volume type and speed type according to their working principles
-
08/12/2020
Causes and troubleshooting of refrigeration solenoid valve failure
The refrigeration solenoid valve is an industrial equipment controlled by electromagnetic, used in the industrial control system to adjust the direction, flow, speed and other parameters of the medium.
-
09/08/2020
Compressed air filter selection method and related technical parameters
In the air compressor system, the air processed by the air compressor cannot be used directly. It must be purified by the dryer filter before it can be put into the air equipment. The role of the filter in the air compressor system is to remove liquid water, dust, oil, dust and other impurities in the compressed air.