Okmarts Pro-face HMI FP3710-T42-24V-U Pro-face HMI FP3710-T42-24V-U, okmarts Online Average rating: 4.6, based on 89 reviews

Pro-face HMI FP3710-T42-U

Pro-face HMI FP3900-T41

Pro-face HMI FP3710-T42-24V-U

Pro-face HMI Touch Screen 15-INCH Rating:24VDC
Availability: In stock
* Shipping calculated at checkout.

Packing and shipping

Packaging Regulation :

Wooden box

Delivery time :

7~14 days(About)

Conditions :

New and Genuine


Functional Specifications

Display Type


Display Size



1,024 x 768 pixels (XGA)

Dot pitch

W0.297 x H0.297 mm [W0.01 x H0.01 in.]

Effective Display Area

W304.1 x H228.1 mm [W11.97 x H8.98 in.]

Display Colors

16,777,216 Colors


LED backlight (The backlight cannot be replaced by the user. The unit must be sent back for backlight replacement.)

Brightness Control


Contrast Control


Backlight Service Life

50,000 hrs. or more (continuous operation at 25 °C before backlight brightness decreases to 50% or backlight starts to blink)

Touch Panel Type

Resistive Film (analog)

Touch Panel Resolution

1,024 x 1,024

Touch Panel Service Life

1,000,000 times or more

Touch Panel Interface

RS-232C or USB (USB2.0, TYPE-B)


Conforms to USB2.0 (TYPE-A) x 1, Power Supply Voltage: DC 5 V ±5 %, Output Current: 500 mA or less, Communication Distance: 5 m or less


Analog RGB input connector: mini D-Sub15 (socket) x 1,<br>
DVI-D input, Connector: DVI-D 24 pin (socket) x 1*2

1.Specified on OSD setting.

2.- FPs which have a mark in hardware revision "2" support DVI Hot Plug Detect function.
- DVI-D Cable FP-DV01-100(10m) can be used with PL-3000B (Revision B or later) and PS2000B.
- PS4000 Series can be connected with FP unit's revision "2" or later and DVI-D Cable FP-DV01-50(5m).
- For connection with the FP which is not marked on Rev. "2", connection may not be made with a DVI-D interface of the FP.
In that case, use an analog RGB interface of the FP.
- We will recommend the resolution of PS4000, PL3000B, PS2000B and PC/AT compatible to change to the maximum display resolution of FP additionally.

General Specifications

Rated Input Voltage

DC 24V

Input Voltage Limits

DC 19.8 to 28.8V

Allowable Voltage Drop

5 ms or less

Power Consumption

40 W or less

In-Rush Current

30 A or less

Voltage Endurance

AC1000V 20mA for 1 minute (between charging and FG terminals)

Insulation Resistance

DC500V 10MΩ or more (between charging and FG terminals)

Surrounding Air Temperature

0 to 50 °C (32 to 122 °F)

Storage Temperature

-20 to 60 °C (-4 to 140 °F)

Ambient Humidity

10 to 90 % RH (Wet bulb temperature: 39 °C or less - no condensation.)

Storage Humidity

10 to 90 % RH (Wet bulb temperature: 39 °C or less - no condensation.)


0.1 mg/m³ or less (non-conductive levels)

Pollution Degree

For use in Pollution Degree 2 environment


Free of corrosive gases

Air Pressure (altitude range)

800 to 1,114 hPa (2,000 m [6,561ft.] above sea level or less)

Vibration Resistance

IEC/EN61131-2 compliant, 5 to 9 Hz Single amplitude 3.5 mm [0.14 in.], 9 to 150 Hz Fixed acceleration: 9.8 m/s², X, Y, Z directions for 10 cycles (100 min)

Concussion Resistance

IEC/EN61131-2 compliant, 147 m/s², X, Y, Z directions for 3 times

Noise Immunity

Noise Voltage: 1,000Vp-p, Pulse Duration: 1μs, Rise Time: 1ns

Electrostatic Discharge Immunity

Contact Discharge Method: 6 kV (IEC/EN61000-4-2 Level 3)


Protective grounding: Grounding resistance of 100 Ω, 2 mm² or thicker wire, or your country's applicable standard. (Same for FG and SG terminals)


Equivalent to IP65f (on the front panel when properly installed in an enclosure)*3

Installation Configuration

Embedded panel

Cooling Method

Natural air circulation

Weight Approx.

7 kg [15.4 lb] or less (display unit only)

External Dimensions

W395 x H294 x D60 mm [W15.55 x H11.57 x D2.36 in.]

Panel Cut Dimensions

W383.5 x H282.5 mm [W15.1 x H11.12 in.], Panel thickness area: 1.6 to 10 mm [0.06 to 0.39 in.]*4

3.The front face of the FP unit, installed in a solid panel, has been tested using conditions equivalent to the standards shown in the specification. Even though the FP unit's level of resistance is equivalent to these standards, oils that should have no effect on the FP can possibly harm the unit. This can occur in areas where either vaporized oils are present, or where low viscosity cutting oils are allowed to adhere to the unit for long periods of time. If the FP's front face protection sheet becomes peeled off, these conditions can lead to the ingress of oil into the FP and separate protection measures are suggested., Also, if non-approved oils are present, it may cause deformation or corrosion of the front panel's plastic cover. Therefore, prior to installing the FP be sure to confirm the type of conditions that will be present in the FP's operating environment., If the installation gasket is used for a long period of time, or if the unit and its gasket are removed from the panel, the original level of the protection cannot be guaranteed. To maintain the original protection level, be sure to replace the installation gasket regularly.

4.Regarding dimensional tolerance, everything +1/-0 mm [+0.04/-0 in.] and R in angle are below R3 [R0.12 in.].



Write Your Own Review
Only registered users can write reviews. Please Sign in or create an account