Industrial Relay
KUEP Series Panel Plug-in Relay
10 amp current rating
TYCO Relay KUEP-11A35-120
People who bought this item also viewed
SIEMENS Relay 3TK2824-1AL20
JEL Relay S1C-225WDV
TOGAMI Relay TJ-125-3F
Riken Relay RAB-150N
Schneider Transformer ABT7PDU100B
ABB Circuit Breaker 10138226
TENGEN Contactor CJ19-25
OBO Surge Protection Device V10-C/1+NPE
DAITO Fuse HM05
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
OKTY Oil Seal TC(NBR)125*150*15
PROFIT Planetary Reducer PL80-10
HONOR Hydraulic Motor 1MM1P05
Recent related posts
-
03/13/2022
8 Reasons Why Your Samsung Fridge Compressor not Working
Almost all families have their own refrigerators, and Samsung fridges have been outstanding.
-
08/05/2020
The difference between the three types of evaporators dry, flooded, and falling film evaporators
The refrigerant in the dry evaporator passes through the heat exchange tube, and the cold water runs outside the high-efficiency heat exchange tube. Such a heat exchanger has relatively low heat exchange efficiency,
-
08/18/2020
Solutions to HVAC water cycle failures
What are the common problems that occur during HVAC operation? What are the solutions? Come and find out with the editor of okmarts.com!<br></br> 1. Pay attention to pipeline quality.<br></br>
-
07/30/2020
About inverter air conditioner fault repair skills
Today I will share with you the maintenance ideas and cases about the failure of the inverter air conditioner that does not heat but can cool. If you like, you can like it and collect it, thank you!!!<br></br>
-
06/15/2020
Causes and solutions of frequent start-up of central air-conditioning compressors
Causes and solutions of frequent start-up of central air-conditioning compressors Central air-conditioning compressor Air conditioner compressor frequent start fault solution We sometimes encounter frequent start-up of air conditioner compressor, s 器2 䀀 ᅵ皥 䖒皦즠Ʋ㉄ᰙ 㲈Ʋ 䌁皦 ᮔDž༬皧㉎ᰙЀ 呄ᠾ鹨់༹皧 ࠄ 00령ꐱ댁珵뛐珵Љ 䕄ྦ 뤂ᐱ뚜珵 ᴴᏩ呄ᠾ퍘ᒥ 鹨់ᩄ ꋔྦ 瑉浥 巠皱㙲皦抐皱 巠皱 ੨皦柘皱 ᅵ皥 ب 巠皱㙲皦忈皱 ੨皦柘皱 즠Ʋǜ 勁皦즠Ʋب ǜ V / 펔B䌁皦 ᮔDž '鱤džၜ먢䇨珵呈ᠾ뤂ᐱ ⿇⬿먲僧ᐱ㥲ᐲ�僬㣢ᐲ ᠾ 랖僧ը 識 �僬㣢ᐲ 臆S㥲ᐲ ᬄğ 識 理艏S杴 識杴 㥲ᐲ
-
09/21/2020
The sealing problem of scroll type automobile air-conditioning compressor
During the mutual movement between the end face of the scroll tooth and the bottom of the scroll plate of the oil-free scroll compressor, the sealing and lubrication function of the end face of the tooth will be affected due to the inability to form an oil film.
-
06/13/2020
Noise of air-conditioning compressors noise from outdoor air-conditioning units and compressors in supermarkets disturbs people
Noise of air-conditioning compressors noise from outdoor air-conditioning units and compressors in supermarkets disturbs people Noise of air-conditioning compressors: noise from outdoor air-conditioning units and compressors in supermarkets disturbs peop
-
07/21/2020
How to protect the refrigeration compressor, you must master the following knowledge!
When the compressor is running, some abnormal conditions may occur, such as: exhaust pressure is too high, suction pressure is too low, oil pressure is insufficient, motor is overheated, excess liquid enters the cylinder, etc. In the event of an abnormal situation, the compressor will be damaged if there is no protective measure.
-
08/16/2020
Why is the temperature too low after the cold storage is installed
After the cold storage is built, the first thing should be tested, so that we can know whether there will be problems after the cold storage is installed. Such a problem needs to be considered in the initial stage of the general cold storage installation.
-
09/21/2020
Calculation and determination of gas consumption
The traditional method of determining the compressed air requirements of a new plant is to add up the air consumption (m3/min) of all air-consuming equipment, and then consider adding a safety, leakage and development factor