Rockwell A-B Sensor 872C-D2NN8-D4

08/08/2020

Types and differences of various refrigerants

Types and differences of various refrigerants 1. R22 is widely used in my country. Some experts believe that if R123 can finally be lifted, then the day when R22 is lifted will not be far away.

06/14/2020

What to do if the air conditioning refrigeration effect is not good

The summer is hot, and air conditioning is an indispensable home appliance product. However, most owners will encounter problems with the poor cooling effect of the air conditioner in the process of using the air conditioner. What is the problem with the 器2䀀
ￜ皥
䖒皦즠Ʋ嫜ི㲈Ʋ
䌁皦
ᮔDž༬皧嫦ིЀ呄ᠾ鹨់༹皧
ࠄ
00령ꐱ댁珵뛐珵Љ
䕄ྦ￿￿뤂ᐱ뚜珵ᴴᏩ呄ᠾ퍘ᒥ鹨់ᩄꋔྦ
瑉浥巠皱㙲皦抐皱巠皱੨皦柘皱ￜ皥
ب巠皱㙲皦忈皱੨皦柘皱
즠Ʋǜ勁皦즠ƲبǜV /펔B䌁皦

08/20/2020

What are the preparations before starting the chiller

Water chiller is an energy-saving machine that achieves cooling effect through vapor compression or absorption cycle. Chillers are called cooling water circulation machines, also called chillers,

06/29/2020

Several causes of compressor burning

09/04/2020

The advantages and disadvantages of centrifugal air compressors, screw air compressors, and piston air compressors

There are many types of air compressors. The following okmarts.com editor introduces the three most common air compressors, namely centrifugal air compressors, screw air compressors, and piston air compressors, and understands and analyzes their respective advantages and disadvantages.

06/14/2020

Common failures of half-sealed piston compressors

Common failures of half-sealed piston compressors 1. The compressor cannot start normally 1. First check whether the power supply voltage is too low or the motor line is poorly connected. If the grid voltage is too low, start again after the grid volt器2䀀
ￜ皥
䖒皦즠Ʋ娼ི㲈Ʋ
䌁皦
ᮔDž༬皧婆ིЀ呄ᠾ鹨់༹皧
ࠄ
00령ꐱ댁珵뛐珵Љ
䕄ྦ￿￿뤂ᐱ뚜珵

09/09/2020

The influence of machining on fatigue life

The residual compressive stress introduced by shot blasting/shot peening is a percentage of the final tensile stress strength, and this ratio increases as the strength/hardness of the part material itself increases. High-strength/hardness metals are more brittle and more sensitive to surface defects. Shot blasting/shot peening will allow these high-strength metals to be used in fatigue-prone working conditions. Aircraft landing gear is usually designed with a fatigue strength of 300 ksi (2068 MPa), combined with shot blasting/shot peening.

06/14/2020

The master disassembles the high-resolution atlas of the refrigeration compressor

The master disassembles the high-resolution atlas of the refrigeration compressor Share the process of dismantling and repairing the refrigerator compressor of a forum master

05/11/2023

Thermal Expansion Valve (TXV): Everything You Need To Know

The thermal expansion valve (TXV) is an important part of the refrigeration device and one of the four basic components in the refrigeration system.

06/14/2020

Note! Seven mistakes in the maintenance of refrigeration equipment

Many refrigeration maintenance masters, seeing the internal leakage of the refrigerator, will directly add the condenser net without pressure, and it will not leak again for a long time. It turns out that it is the evaporator of the refrigerator compartme器2䀀
ￜ皥
䖒皦즠Ʋ煔क़㲈Ʋ
䌁皦
ᮔDž༬皧煞क़Ѐ呄ᠾ鹨់༹皧
ࠄ
00령ꐱ댁珵뛐珵Љ
䕄ྦ￿￿뤂ᐱ뚜珵ᴴᏩ呄ᠾ퍘ᒥ鹨់ᩄꋔྦ
瑉浥巠皱㙲皦抐皱巠皱੨皦柘皱ￜ皥
ب巠皱㙲皦忈皱੨皦柘皱
즠Ʋǜ勁皦즠ƲبǜV /펔B䌁皦
ᮔDž'鱤džၜ먢䇨珵呈ᠾ뤂ᐱ⿇⬿먲僧ᐱ㥲ᐲ�僬㣢ᐲᠾ
랖僧ښ識�僬㣢ᐲ臆S㥲ᐲᬄğ識理艏S杴 識杴 㥲ᐲ