UNI-CROWN Vacuum Pump UN-25N
- Specifications
- Q&A
- Reviews
Voltage:AC 110/220V Vacuum:550mmHg
Open Flow:18(60Hz)/15(50Hz)LPM
Power Consumption:90W
NASH Vacuum Pump 2BV2061ONC022P
Iwaki Magnet Pump MDG-H15KA200S15
SEKO Diaphragm Pump DMS201
EMAUX Water Pump EPH400 380V
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
Banner Sensor Q20PLPQ
Sanyo Denki Fan 109P042H316
AirTAC Air Cylinder ACE20X25S
09/06/2020
Permanent magnet materials commonly used in motors include sintered magnets and bonded magnets. The main types are AlNiCo, ferrite, samarium cobalt and neodymium iron boron.
06/14/2020
Duct and ceiling machine maintenance and troubleshooting The air duct machine is the simplest central air conditioning unit. It is divided into small air ducts and large air ducts according to the cooling and heat limits of the unit. Below 10P is called 器2 䀀 ᅵ皥 䖒皦즠Ʋ嫜ི 㲈Ʋ 䌁皦 ᮔDž༬皧嫦ིЀ 呄ᠾ鹨់༹皧 ࠄ 00령ꐱ댁珵뛐珵Љ 䕄ྦ 뤂ᐱ뚜珵 ᴴᏩ呄ᠾ퍘ᒥ 鹨់ᩄ ꋔྦ 瑉浥 巠皱㙲皦抐皱 巠皱 ੨皦柘皱 ᅵ皥 ب 巠皱㙲皦忈皱 ੨皦柘皱 즠Ʋǜ 勁皦즠Ʋب ǜ V / 펔B䌁皦 ᮔDž '鱤džၜ먢䇨珵呈ᠾ뤂ᐱ ⿇⬿먲僧ᐱ㥲ᐲ�僬㣢ᐲ ᠾ 랖僧Մ 識 �僬㣢ᐲ 臆S㥲ᐲ ᬄğ 識 理艏S杴 識杴 㥲ᐲ
06/14/2020
Compressor noise control is an extremely complex problem. What are the possible reasons for the noise of air-conditioning compressors? Only when the cause is found can the solution be found accordingly.
03/02/2021
1.Positioning or residual torque: when there is no current passing through the winding, the torque required to make the output shaft of the motor rotate. 2.Driver: an electrical control device used to run the stepping motor. This includes power supply, logic programmer, switching element and a variable frequency pulse source which determines the step rate. 3.Dynamic torque: the torque produced by the motor at a certain step rate. The dynamic torque can be expressed by PULL IN torque or PULL OUT torque.
08/15/2020
Before using the air-cooled chiller, you can carefully count the operating data of the equipment, and then based on these operating data, you can make a basic judgment on the operating status of the equipment,
12/14/2021
HMI is the device connects the user and the machinery system. It is the medium of information transfer and exchange between people and machines. Since the first button switch was developed, man-machine interface monitoring system has become an essential part of industrial production.
07/26/2020
The compressor is the "heart" of the refrigeration system. The compressor sucks low-temperature and low-pressure refrigerant gas from the suction pipe, drives the piston to compress it through the operation of the motor, and then discharges the high-temperature and high-pressure refrigerant gas to the exhaust pipe to provide power for the refrigeration cycle to realize the refrigeration cycle. The editor summarizes the common faults and troubleshooting methods of the compressor to help you better maintain the compressor.
08/04/2020
The condenser is one of the important equipment in the refrigeration system. It transfers the heat of the superheated vapor of the refrigerant to the surrounding air or water through the heat-releasing surface of the condenser
03/12/2021
The controller is usually a computer or PID control circuit, and its main task is to transform and process the deviation signal output by the comparison element, so as to control the executive element to act as required.
07/02/2020
How is the compression process of the PFM compressor One of the PFM compressors is a scroll compressor. How is its compression process completed? We can find the answer in this article. First of all, we must know that there are two scrolls in the upper part of the PFM compressor, a moving scroll and a static scroll.