Voltage: three phase
Input: AC 3PH 380-480V 50-60HZ
Output: AC 3PH 0-480V 0-400HZ
Yaskawa VFD Frequency Converter CIMR-VB4A0038FMA
People who bought this item also viewed
BEST VFD Frequency Converter FC300-5.5-T4
Yolico VFD Frequency Converter YD3093-T4N
Yaskawa Servo Motor SGMGV-30A3A6B
Omron HMI NT20S-ST161B-EV3
TR Encoder CEV65S-10056
Yaskawa VFD Frequency Converter CIMR-G7A2055
Mean Well Power Supply SP-480-3.3
MITSUBISHI Spindle Amplifier MDS-DM2-SPV3-20080
DIEWU NIC Card 82540
Schneider Input Output Module MES108
SONGCHUAN Relay HV012-1AH-C-24VDC
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
ODE Solenoid Valve 21HT4KOY160-S
HONGYI Vane Pump 45V-75A-86
HENGSTLER Encoder RI58-O/20EK.42KG
Festo Air Cylinder DSNU-25-30-PPV-A
Siemens Circuit Breaker 5SY4332-7
SIEMENS Servo Motor 1FK7083-5AF71-1KG5
Recent related posts
-
08/02/2020
Refrigerator refrigeration system leak detection
The refrigeration system should be tested for leaks due to refrigerant leakage or refrigerators after replacing parts. The following three methods are generally used for leak detection in refrigeration systems
-
09/09/2020
The influence of machining on fatigue life
The residual compressive stress introduced by shot blasting/shot peening is a percentage of the final tensile stress strength, and this ratio increases as the strength/hardness of the part material itself increases. High-strength/hardness metals are more brittle and more sensitive to surface defects. Shot blasting/shot peening will allow these high-strength metals to be used in fatigue-prone working conditions. Aircraft landing gear is usually designed with a fatigue strength of 300 ksi (2068 MPa), combined with shot blasting/shot peening.
-
06/13/2020
Centrifugal compressor2
Centrifugal compressors, also known as turbine compressors, are mainly used to compress gas. They are mainly composed of a rotor and a stator: the rotor includes an impeller and a shaft, and the impeller has blades, a balance disk, and a part of the shaft 器2 䀀 ᅵ皥 䖒皦즠Ʋ焬क़ 㲈Ʋ 䌁皦 ᮔDž༬皧然क़Ѐ 呄ᠾ鹨់༹皧 ࠄ 00령ꐱ댁珵뛐珵Љ 䕄ྦ 뤂ᐱ뚜珵 ᴴᏩ呄ᠾ퍘ᒥ 鹨់ᩄ ꋔྦ 瑉浥
-
09/25/2023
Chilled Water System: Basics, Working Principle Diagram, Types and More
A chilled water system is a type of HVAC (heating, ventilation, and air conditioning) system that provides cooling through the circulation of chilled water.
-
06/13/2020
What is an air-cooled heat pump Introduction of knowledge about air-cooled heat pump
What is an air-cooled heat pump Introduction of knowledge about air-cooled heat pump What is an air-cooled heat pump-Introduction to an air-cooled heat pump
-
06/13/2020
How to distinguish original refrigeration compressors from second-hand compressors
How to distinguish original refrigeration compressors from second-hand compressors How to distinguish the original refrigeration compressor from the second-hand refrigeration compressor? In fact, this is the same as the RMB identification method, and it 器2 䀀 ᅵ皥 䖒皦즠Ʋ煔
-
04/30/2022
How to Judge The Model of AC Contactor?
Contactor is the most basic and common electrical component in relay control system. It is mainly used to connect and disconnect lines, or frequently control the operation of motors and other equipment.
-
07/25/2020
90% of the compressor burns down due to these reasons (Refrigeration Oil)
The common faults of compressors mainly include the following three types: 1. Motor burns; 2. Oil shortage caused by refrigerating oil; 3. Liquid shock.
-
06/13/2020
Don't panic if the refrigeration compressor suddenly stops, remember these methods!
What should be paid attention to when the refrigeration compressor stops abnormally? Some friends may not understand it. Let's take a look at it with everyone today!
-
08/20/2020
The reason why the compressor of industrial chiller cannot start
What is the reason why the industrial chiller cannot be started? The compressor is the core part of the industrial chiller. If it cannot be started, the entire unit cannot operate normally. When the compressor is started,