WESTLOCK Switch 2245ABYN0CS42XAI-AR3
Type: Switch
Brand: WESTLOCK
Type: Switch
Brand: WESTLOCK
Type: Switch
Brand: WESTLOCK
PILZ Switch 570500
Siemens Switch 3SU1002-2BM10-0AA0
Omron Switch D4B-2A71N
Balluff Switch BES 516-325-G-E4-C-02
Rockwell A-B Sensor 42JSEZ-D1LPA1-A2
Shihlin Circuit Breaker BW-2000C 3P 1600A
Schneider Contactor LC1D40AN7
KOSMEK Overload Pump PL-1071-HA
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
10/16/2020
Insufficient compressor displacement has a great impact on the entire refrigeration system. If it is not repaired and handled in time, it may cause problems such as the cylinder, cylinder head rupture, and compressor water intake, which will destroy the entire refrigeration system cycle. It may even cause accidents such as compressor combustion and explosion. So what causes the insufficient displacement of Copeland compressor? Let's take a look.
08/11/2020
he closer the main unit of the refrigeration unit is to the evaporator, the better it is easy to maintain and has good heat dissipation. If it is moved outside, it needs to install a canopy.
06/14/2020
Explain "Overcooling" and "Overheating"-The Basics Misunderstanding: subcooling ≠ condenser inlet temperature-condenser outlet temperature The so-called "undercooling": That is, the saturated liquid after condensation is re-cooled through a certain 器2 䀀 ᅵ皥 䖒皦즠Ʋ煔क़ 㲈Ʋ 䌁皦 ᮔDž༬皧煞क़Ѐ 呄ᠾ鹨់༹皧 ࠄ 00령ꐱ댁珵뛐珵Љ 䕄ྦ 뤂ᐱ뚜珵 ᴴᏩ呄ᠾ퍘ᒥ 鹨់ᩄ ꋔྦ 瑉浥 巠皱㙲皦抐皱 巠皱 ੨皦柘皱 ᅵ皥 ب 巠皱㙲皦忈皱 ੨皦柘皱 즠Ʋǜ 勁皦즠Ʋب ǜ V / 펔B䌁皦 ᮔDž '鱤džၜ먢䇨珵呈ᠾ뤂ᐱ ⿇⬿먲僧ᐱ㥲ᐲ�僬㣢ᐲ ᠾ 랖僧Ѥ 識 �僬㣢ᐲ 臆S㥲ᐲ
06/29/2020
Analysis of the cause of excessive suction temperature of compressor The high suction temperature is mainly due to the increase of superheat of suction. Note that high suction temperature does not mean high suction pressure, because the suction is superheated steam. Under normal circumstances, the compressor cylinder head should be half cold and half hot. If the suction temperature is too high, the cylinder head will all heat up.
04/18/2022
Because the output signal of the sensor is very small, it is usually only a few millivolts. In order to improve the anti-interference ability of the instrument, the zero potential in the input circuit must be grounded
09/05/2020
The air compressor air filter (also known as style) is composed of an air filter assembly and a filter element. The outside is connected to the air compressor's intake valve through a joint and a threaded tube to filter the dust, particles and other impurities in the air.
07/18/2022
Before installing the gear pump, please check whether the pump and motor are damaged during transportation, or dirt enters the pump cavity due to the loss and rupture of the dust cover.
09/08/2020
1. Adsorbent Adsorbent is the material basis of the adsorption dryer. The type of adsorbent has a decisive influence on the final dew point of the compressed air being processed. At present, the most commonly used adsorbents in compressed air dehydration and drying are silica gel,
09/14/2020
When the refrigerant liquid entering the evaporator is too much or the evaporation pressure is too low, the cold The medium liquid will be sucked into the compressor. Since the refrigerant liquid is incompressible,
06/25/2020
The air-conditioning compressor plays the role of compressing and driving the refrigerant in the air-conditioning refrigerant circuit. The working circuit is divided into an evaporation area (low pressure area) and a condensation area (high pressure area). The indoor unit and outdoor unit belong to the high-pressure or low-pressure area (depending on the working state), and the compressor is generally installed in the outdoor unit.