Basic dynamic load rating: C 1330 N
Basic static load rating: C0 1890 N
IKO Linear Guideway LWL7C1 Linear way Lwith one slide unit
People who bought this item also viewed
IKO Linear Guideway LWLF42 Linear way L
THK Linear Guideway SHS35LV1SS
HIWIN Linear Guideway HGH30CAH
THK Linear Guideway SHS25LV1UU
THK Linear Guideway SHS30LV1UU
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
Shilin Contactor S-P21 32
GSD Water Pump GMP35-65/2P
MITSUBOSHI Belt S3M-537-20
Honeywell Sensor 83298-00000100-01
NORGREN Ball Valve 602112168
Rockwell A-B Sensor 871TM-DH4NE12-D4
Recent related posts
-
05/02/2022
Differences Between AC Contactor and DC Contactor?
The working principle of DC contactor is similar to that of AC contactor. They all make the main contact on or off through the actuation of electromagnetic coil.
-
09/03/2021
How to Communicate PLC to VFD
PLC (Programmable Logic Controller) and VFD (Variable Frequency Drive) play an important role in industrial production and technological development.
-
09/16/2020
Application skills of air compressor using oil and gas separator
Abstract: The application technical requirements of the oil-gas separation core used in air compressors, and the problems that occur during the use of the oil-gas separation core are analyzed, and the matters to be noted before installation.
-
09/09/2020
The influence of machining on fatigue life
The residual compressive stress introduced by shot blasting/shot peening is a percentage of the final tensile stress strength, and this ratio increases as the strength/hardness of the part material itself increases. High-strength/hardness metals are more brittle and more sensitive to surface defects. Shot blasting/shot peening will allow these high-strength metals to be used in fatigue-prone working conditions. Aircraft landing gear is usually designed with a fatigue strength of 300 ksi (2068 MPa), combined with shot blasting/shot peening.
-
06/14/2020
The reason for the frost on the compressor air inlet is here!
The reason for the frost on the compressor air inlet is here! Frost on the air inlet of the cold storage compressor is a very common phenomenon in the refrigeration system. Under normal circumstances
-
08/20/2020
Analysis and troubleshooting of common faults in cold and hot water air conditioning systems
Common faults of cold and hot water air conditioning systems mainly come from three major parts: the refrigeration system, the water pipe system and the surrounding environment.
-
09/30/2022
Servo Motor: Basics, Work Principle & Selection
This article introduces the basic knowledge, working principle, selection and related FAQs of servo motors.
-
06/21/2020
Will the air compressor explode_The cause and measures of air compressor explosion
Will the air compressor explode_The cause and measures of air compressor explosion Will the air compressor explode <img src="{{media url="Will_the_air_compressor_explode_The_cause_and_measures_of_air_compressor_explosion.jpg"}}" alt="" /> The air compressor will explode. However, air compressors are not easy to explode. The accident rate of the air storage tank of the piston type air compressor is very small. Only when the air pressure switch and the safety valve of the air compressor are broken at the same time will the air compressor have the possibility of explosion.
-
06/14/2020
Causes, treatment and prevention of liquid shock in refrigeration compressor
Causes, treatment and prevention of liquid shock in refrigeration compressor Liquid shock refers to the situation where the refrigerant fails to absorb heat or evaporates sufficiently, and the refrigerant liquid or wet steam is sucked into the compressor 器2 䀀 ᅵ皥 䖒皦즠Ʋ焬क़ 㲈Ʋ 䌁皦
-
07/25/2020
How to distinguish between original refrigeration compressor and second-hand refrigeration compressor?
At present, illegal businesses on the market often use second-hand or refurbished or offline refrigeration compressors to make industrial chillers in order to make huge profits. They are used in some water-cooled industrial chillers, air-cooled industrial chillers, and screw-type water-cooled industrial chillers.