Collector Emitter maximum voltage:1200 V
Continuous Collector Maximum Current:450 A
INFINEON IGBT Module FS300R12KE4
People who bought this item also viewed
Kuroda Module PT-04RC2
Beckhoff Switch Module CU1521-0010
Beckhoff Module KL3062
Beckhoff Module EL7041-1000
SIEMENS Servo Motor 1FK7083-2AC71-1RG1
Lenze Servo Drive EVS9322-ESV004
Nemicon Encoder HEF-30-2MHC
Siemens PLC 6ES7221-1BH22-0XA8
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
PARKER Filter G01990
BANDO Belt T2.5-120-15
TYCO Relay PT570T30
Honeywell Sensor 19C050PA2K
ABB Circuit Breaker S201M-B2
Recent related posts
-
09/08/2020
Dew point of adsorption dryer and its influencing factors
1. Adsorbent Adsorbent is the material basis of the adsorption dryer. The type of adsorbent has a decisive influence on the final dew point of the compressed air being processed. At present, the most commonly used adsorbents in compressed air dehydration and drying are silica gel,
-
07/21/2020
How to protect the refrigeration compressor, you must master the following knowledge!
When the compressor is running, some abnormal conditions may occur, such as: exhaust pressure is too high, suction pressure is too low, oil pressure is insufficient, motor is overheated, excess liquid enters the cylinder, etc. In the event of an abnormal situation, the compressor will be damaged if there is no protective measure.
-
06/13/2020
Causes and harms of non-condensable gas produced by refrigeration system
Non-condensable gas refers to air, hydrogen, nitrogen, lubricating oil vapor, etc. mixed in the refrigeration system.
-
06/19/2020
How to properly clean the air conditioner yourself
After a winter of inactivity, the air conditioner that has been "dusted" for a long time is reactivated. It is believed that most of the friends are directly plugged in and turned on. In fact, this is not correct. <img src="{{media url="How_to_properly_clean_the_air_conditioner_yourself.jpg"}}" alt="" /> It is necessary to know that the air conditioner has accumulated dust and breeds bacteria after being left for a long time. Blowing out with the wind seriously threatens your health. This is actually due to the working principle of the air conditioner: when cooling, the room temperature air is continuously sucked in, filtered by the filter, and then cooled by the fins of the heat exchanger, and finally the cold air is blown out, and then returned to the room for reciprocating circulation.
-
08/20/2020
The reason why the compressor of industrial chiller cannot start
What is the reason why the industrial chiller cannot be started? The compressor is the core part of the industrial chiller. If it cannot be started, the entire unit cannot operate normally. When the compressor is started,
-
06/19/2020
What are the causes of air conditioning trip
What are the causes of air conditioning trip 1. The contradiction between the rated current of the air conditioner and the current carrying capacity of the wire. Here are two formulas involved: ①The rated current of air conditioner I=P÷U ÷power factor, the power remains unchanged, the smaller the voltage, the greater the current required. ② The current carrying capacity of the wire I=U÷R, the voltage is proportional to the current. So when the power supply voltage is normal, we must consider the line voltage drop. The longer the line, the greater the resistance, the greater the voltage drop, and the smaller the output current at the end. However, because the power of the load remains unchanged, the voltage becomes smaller, and the current that needs to be output will be larger. At this time, the wire is forced to overload, and the time will cause heating, and eventually cause the tripping of the open circuit. Some friends said that the heat of the wire will not cause the tripping of the circuit breaker. In fact, the manufacturer of the air switch has made it clear in the relevant manuals that the heat of the wire will cause the air switch to trip. Because the wire heats up, the crimp terminal will also heat up, and the resistance will become larger and larger. The larger the resistance, the greater the current consumption, and the hotter it will be, a vicious cycle. 2. Leakage During the daily maintenance work, we will encounter the situation that the air circuit trips due to the leakage of electricity. At least I have not experienced it once or twice. Regardless of the leakage of the neutral line or the leakage of the live line, a long time will cause the circuit breaker to trip. Why does the electric leakage cause the MCB to trip? There are two situations. ① Good grounding. At the beginning, the leakage current was not large, and as time went by, the leakage current became larger and larger, and eventually evolved into a short circuit to ground, unable to close. ②There is no ground wire. If the equipment is not connected to the protective ground, when the wire leaks to the equipment, it is equivalent to adding a large shunt resistance. Like this problem, if the air conditioner does not have a ground wire, when the wire leaks to the air conditioner, the air conditioner is a very large shunt resistor and will consume a lot of current. Eventually, the wire will heat up or trip open. How to determine whether the trip caused by the above two aspects can be done with a clamp ammeter. ① Measure the voltage at the input and output to see if there is a significant change in voltage drop. ②Measure whether the output current exceeds the standard. So my suggestion is: first measure the supply voltage to see if it is within the allowable fluctuation range. Then measure the current to see if it exceeds the rated ampacity of the wire. Finally, check the data one by one according to the measured data to find out the reason.
-
04/12/2024
Servo Motor Applications: a Complete Guide
Servo motors are widely used in various mechanical equipment. It has the characteristics of fast response, high precision and high reliability, and can achieve precise position control, speed control and force control.
-
09/08/2020
4 advantages of oil-free screw air compressor
Oil-free screw air compressors are more and more widely used. The lubrication, sealing and cooling of the entire main engine are completed by water. Therefore, oil-free screw air compressors can be described as true oil-free energy-saving air compressors.
-
08/09/2020
The harm of overheating of industrial water chiller to equipment during use
The overheating problem of industrial chillers has a serious negative impact on the efficiency of the equipment. In order to maintain the safety and stability of industrial chillers, when using industrial chillers,
-
07/23/2020
Reasons for excessively high discharge temperature of refrigeration compressor (technology sharing)
The refrigeration compressor is the core and heart of the refrigeration system. The capacity and characteristics of the compressor lead to the capacity and characteristics of the refrigeration system. In a sense, the design and matching of the refrigeration system is to reflect the capacity of the compressor.