Kuebler Encoder 8.5020.4521.1024

06/29/2020

Compression ratio of American Copeland compressor

08/20/2020

Operation management of wet stroke of refrigeration compressor

The wet stroke of the compressor is caused by the liquid refrigerant entering the cylinder. When the amount of liquid entering is small, frost will form on the outside of the cylinder.

06/14/2020

The principle, installation and use of the bypass valve of the heater of the cold dryer Composition and principle of "heater bypass"

The principle, installation and use of the bypass valve of the heater of the cold dryer Composition and principle of "heater bypass" The energy regulation of the system is generally composed of the following ways: Compressor parallel-multi-stage contro器2䀀
ￜ皥
䖒皦즠Ʋ嫜ི㲈Ʋ
䌁皦
ᮔDž༬皧嫦ིЀ呄ᠾ鹨់༹皧
ࠄ
00령ꐱ댁珵뛐珵Љ

07/26/2020

This is a common failure of refrigeration compressors!

The excessively high suction temperature is mainly caused by the increase of suction superheat. Note that high suction temperature does not mean high suction pressure, because suction is superheated steam.

08/21/2020

Is the air-conditioning installation nonsense

Many people think that if the air conditioner is bought, the air conditioner in this home will be able to cool and heat super well, but in fact, the installation of air conditioner also has a crucial

07/14/2020

What's wrong with the freezer not cooling

1. Test the power cord with an electric pen. The broken power cord of the freezer is also a cause of non-refrigeration. For this situation, we need to check whether it is a power problem. The general approach is to open the door and observe whether the lighting lamp in the box Light up. Look for signs of damage to the wires, such as being bitten by a mouse.

04/05/2024

Analysis and Solutions to AC Servo Motor Vibration Faults

AC servo motors are used in closed environments and are usually not easily damaged. But if the AC servo motor has vibration failure, what is the reason?

08/17/2020

Five important points for attention when selecting piston chillers

The main control parameters of piston chillers are energy efficiency ratio, rated cooling capacity, input power, refrigerant type, power supply voltage, etc. Below, the editor of okmarts.com introduces the selection points of piston chillers in detail.

09/08/2020

Brief introduction of compressed air purification equipment applicable industries

Compressed air is the second largest power source after electricity. It is also a process gas source with multiple uses. Its application range covers petroleum, chemical industry, metallurgy, electric power, machinery, light industry, textiles, automobile manufacturing, electronics, and food. ,

06/20/2020

What are the causes of air conditioning trip

What are the causes of air conditioning trip 1. The contradiction between the rated current of the air conditioner and the current carrying capacity of the wire. 　　Here are two formulas involved: 　　①The rated current of air conditioner I=P÷U ÷power factor, the power remains unchanged, the smaller the voltage, the greater the current required. 　　② The current carrying capacity of the wire I=U÷R, the voltage is proportional to the current. 　　 So when the power supply voltage is normal, we must consider the line voltage drop. The longer the line, the greater the resistance, the greater the voltage drop, and the smaller the output current at the end. However, because the power of the load remains unchanged, the voltage becomes smaller, and the current that needs to be output will be larger. At this time, the wire is forced to overload, and the time will cause heating, and eventually cause the tripping of the open circuit. 　　 Some friends said that the heat of the wire will not cause the tripping of the circuit breaker. In fact, the manufacturer of the air switch has made it clear in the relevant manuals that the heat of the wire will cause the air switch to trip. Because the wire heats up, the crimp terminal will also heat up, and the resistance will become larger and larger. The larger the resistance, the greater the current consumption, and the hotter it will be, a vicious cycle. 　　 2. Leakage 　　During the daily maintenance work, we will encounter the situation that the air circuit trips due to the leakage of electricity. At least I have not experienced it once or twice. Regardless of the leakage of the neutral line or the leakage of the live line, a long time will cause the circuit breaker to trip. 　　Why does the electric leakage cause the MCB to trip? There are two situations. 　　 ① Good grounding. At the beginning, the leakage current was not large, and as time went by, the leakage current became larger and larger, and eventually evolved into a short circuit to ground, unable to close. 　　②There is no ground wire. If the equipment is not connected to the protective ground, when the wire leaks to the equipment, it is equivalent to adding a large shunt resistance. Like this problem, if the air conditioner does not have a ground wire, when the wire leaks to the air conditioner, the air conditioner is a very large shunt resistor and will consume a lot of current. Eventually, the wire will heat up or trip open. 　　How to determine whether the trip caused by the above two aspects can be done with a clamp ammeter. 　　 ① Measure the voltage at the input and output to see if there is a significant change in voltage drop. 　　②Measure whether the output current exceeds the standard. 　　 So my suggestion is: first measure the supply voltage to see if it is within the allowable fluctuation range. Then measure the current to see if it exceeds the rated ampacity of the wire. Finally, check the data one by one according to the measured data to find out the reason.