Banner Sensor Q25SN6LPW

07/18/2020

Working condition and adjustment of refrigeration system of low temperature chiller

Working condition and adjustment of refrigeration system of low temperature chiller Refrigerators are now widely used in the refrigeration industry, and the refrigerant is usually R22 (also R404a). In order to facilitate operation and maintenance and reduce the installation location, the refrigeration compressor, oil separator, water-cooled shell and tube condenser, filter drier

06/29/2020

Time node of compressor refrigeration oil replacement

Time node of compressor refrigeration oil replacement 1. The long-term operation of the entire refrigeration system, after the initial maintenance, if there are no special circumstances, the compressor refrigeration oil should be replaced when the refrigeration system working time reaches 10,000-12,000 hours.

06/14/2020

Explain "Overcooling" and "Overheating"-The Basics

Explain "Overcooling" and "Overheating"-The Basics Misunderstanding: subcooling ≠ condenser inlet temperature-condenser outlet temperature The so-called "undercooling": That is, the saturated liquid after condensation is re-cooled through a certain器2䀀
ￜ皥
䖒皦즠Ʋ煔क़㲈Ʋ
䌁皦
ᮔDž༬皧煞क़Ѐ呄ᠾ鹨់༹皧
ࠄ
00령ꐱ댁珵뛐珵Љ
䕄ྦ￿￿뤂ᐱ뚜珵ᴴᏩ呄ᠾ퍘ᒥ鹨់ᩄꋔྦ
瑉浥巠皱㙲皦抐皱巠皱੨皦柘皱ￜ皥
ب巠皱㙲皦忈皱੨皦柘皱
즠Ʋǜ勁皦즠ƲبǜV /펔B䌁皦
ᮔDž'鱤džၜ먢䇨珵呈ᠾ뤂ᐱ⿇⬿먲僧ᐱ㥲ᐲ�僬㣢ᐲᠾ
랖僧Ѥ識�僬㣢ᐲ臆S㥲ᐲ

07/29/2025

What is Hydraulic Pump? (Function, Types, Application＆Selection Method)

The basic hydraulic system components include oil tank, hydraulic pump, control valve, oil cylinder, connecting pipe and relief valve.

01/01/2025

How Does a Refrigeration Compressor Work? With Animation for Each Type

Refrigeration compressor is a kind of driven fluid machinery, which promotes low-pressure gas to high-pressure gas and is the heart of refrigeration system.

08/03/2020

Compressor exhaust overheating is not that complicated, just for these few reasons!

The main reasons for the exhaust temperature overheating are as follows:<br></br> 　　 High return air temperature, large heating capacity of the motor, high compression ratio, high condensation pressure, improper refrigerant selection

09/07/2020

Why is air humid after compression

We all know the importance of compressed air drying. This is a critical step in the compressed air process. If you skip this step, it may cause a large amount of water to accumulate in your system. So why does compressed air get wet?

09/22/2020

Compressed air drying and purification system composition

Since compressed air inevitably contains impurities such as solids, liquids, and gases, and each has its own characteristics, it cannot be achieved with a single device. Therefore, compressed air drying and purification becomes a system, a complete compressed air The drying purification system includes: 1) gas-liquid separator; 2) filter; 3) drying equipment and other facilities.

07/17/2020

Piston compressor use and maintenance technology

Preparation before start-up: Operation, repair and maintenance must be carried out by self-made people. The compressor should be unsealed and cleaned before use, and check whether there is rust on each friction surface. The rust phenomenon should be cleaned with oilstone grinding and clean, and the friction surface should be coated with lubricating oil after unsealing.

06/29/2020

Several causes of compressor burning