Displacements 15.2 - 54 cm3/rev
Maximum continuous pressure 300 bar (depending on displacement)
Fluid temperature range -20 / +90 °C (Extreme condition temperature range: 30 +110 °C)*
Recommended fluids hydraulic mineral oil-based
Standard seals material HNBR standard
BUCHER Gear Pump AP-APR212LN-4.5
People who bought this item also viewed
Sumitomo Gear Pump QT62-125F-S1389-A
KOMPASS Check Valve MSW-03-X
TAICIN Overflow Valve JRS-G06-3
Daikin Piston Pump V70SA1ARX-60
Eaton Vickers Vane Pump 3520V-25A14-86CC22R
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
SHAKO Air Cylinder TC40C400
TYCO Relay V23132-A2001-X26
PIZZATO Switch FZ E157-M2
SMC Solenoid Valve SY3120-1LZD-C6
Balluff Sensor BCS008C
Recent related posts
-
09/08/2020
Introduction of micro heat regeneration adsorption dryer
The non-thermal regeneration suction dryer uses the compressed air pressure change, adsorption under high moisture pressure, and desorption under low moisture pressure to regenerate the adsorbent.
-
06/14/2020
Screw compressor overhaul
Screw compressor overhaul Screw compressor overhaul, normal working condition of refrigeration system in operation: 1. The suction temperature of the compressor should be 5-15 ℃ higher than the evaporation temperature; 2. The discharge temperature 器2 䀀 ᅵ皥 䖒皦즠Ʋ焬क़ 㲈Ʋ 䌁皦 ᮔDž༬皧然क़Ѐ 呄ᠾ鹨់༹皧 ࠄ 00령ꐱ댁珵뛐珵Љ 䕄ྦ 뤂ᐱ뚜珵 ᴴᏩ呄ᠾ퍘ᒥ 鹨់ᩄ ꋔྦ 瑉浥 巠皱㙲皦抐皱 巠皱 ੨皦柘皱
-
02/27/2021
Debugging method of servo motor
Before wiring, initialize the parameters. On the control card: select the control method; clear the PID parameters; let the default enable signal turn off when the control card is powered on; save this state to ensure that the control card is in this state when it is powered on again.
-
01/16/2024
Overview of Industrial Fans: Work Principle, Types, Application Areas, Importance and Selection Guide
Industrial fans are fan equipment specially designed for industrial environments, with powerful wind force and stable performance.
-
09/03/2020
What is the maximum flow condition of a centrifugal compressor
The working condition when the flow reaches the maximum is the maximum flow working condition. There are two possibilities for this working condition:
-
09/21/2020
Working principle and usage method of motor bearing grease
Working principle and usage method of motor bearing grease The lubrication of the motor bearing relies on the lubricating oil that is precipitated when the three-dimensional fiber network structure in the grease is broken under the action of shear, forming a layer of lubricating film on the rotating elements of the bearing, the bearing seat and the bearing race for lubrication Effective.
-
06/14/2020
Fresh air system allows you to breathe fresh air at home for 24 hours
Fresh air system allows you to breathe fresh air at home for 24 hours In recent years, poor outdoor air quality has caused sensitive people to induce respiratory diseases;
-
08/07/2020
What is the difference between air-cooled heat pump units and water-cooled heat pump units
What is the difference between air-cooled heat pump units and water-cooled heat pump units Some people have never figured out what is the difference between air cooling and water cooling? The following compares the working principles,
-
07/04/2020
Points to note when installing Taikang Compressor
Points to note when installing Taikang Compressor The air conditioner and cold storage can provide refrigeration without the credit of fluorine and compressor. Taikang Compressor is a common air conditioner and cold storage compressor with good quality and guaranteed.
-
05/06/2023
How Water Source Heat Pumps Work
A heat pump is a device that transfers thermal energy from a low-grade heat source to a high-grade heat source. Heat pumps, driven by electricity, usually first obtain low-grade heat energy from natural air, water or soil, and then provide high-grade heat energy.