Brand: COKERY
Accessory type: Toothed belt for agricultural machinery
Material: Neoprene
COKERY Belt SC69
People who bought this item also viewed
COKERY Belt B130
SYNCHROFLEX Belt AT 3/501
ESBAND Belt PU11 1470×22×3.0
SYNCHROFLEX Belt T 5-255
Sanyo Denki Servo Motor P50B07040HCS00
Mitsubishi Speed Reducer GM-DB 0.4KW 1:100
Crouzet Electric Motor 82862006
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
KUDOM Relay KSJ60D10-L
Recent related posts
-
07/07/2020
Earth Hour: Hitachi Central Air Conditioner works with you to speak for the earth
-
07/13/2020
All basic knowledge of screw air compressor
Danfoss logo (Danfoss) only uses unique red. The (Maneurop) logo is printed on the bottom of the piston compressor label. The nameplate is printed with visible pre-cut lines. If the nameplate is removed, the four corners of the nameplate will be missing.
-
06/13/2020
15 common sense of refrigeration and air conditioning!
1. The air conditioner cannot be restarted immediately after it is turned off After the central air conditioner is shut down, it can only be operated after 3 minutes. This is because the timing protector will automatically work to prevent the compresso 器2 䀀 ᅵ皥 䖒皦즠Ʋ煔क़ 㲈Ʋ 䌁皦 ᮔDž༬皧煞क़Ѐ 呄ᠾ鹨់༹皧 ࠄ 00령ꐱ댁珵뛐珵Љ 䕄ྦ
-
06/13/2020
Cold storage construction guide
Cold storage construction guide Cold storage construction guide 1. Select the appropriate volume and temperature range of the cold storage according to its own use and requirements;
-
06/20/2020
[Experience] What happens if the compressor suction pressure is too high and the discharge pressure is too high
[Experience] What happens if the compressor suction pressure is too high and the discharge pressure is too high Compressor suction pressure is too high, discharge pressure is too high 1. Too much refrigerant. Too much refrigerant will cause the suction pressure and discharge pressure to be too high at the same time. This is because when too much refrigerant fills the reservoir, it will occupy a part of the condenser volume, reducing the heat dissipation area and causing the condenser Poor condensation. Discharge excess refrigerant from the low-pressure side.
-
06/13/2020
Does air conditioning and refrigeration rely on compressors or refrigerants, or both?
Does air conditioning and refrigeration rely on compressors or refrigerants, or both? This question seems to be asking whether to boil water in a kettle, whether it needs boiling water or a kettle. The compressor is a kettle, and the refrigerant is water 器2 䀀 ᅵ皥 䖒皦즠Ʋ嫜ི 㲈Ʋ 䌁皦 ᮔDž༬皧嫦ིЀ 呄ᠾ鹨់༹皧 ࠄ 00령ꐱ댁珵뛐珵Љ 䕄ྦ 뤂ᐱ뚜珵 ᴴᏩ呄ᠾ퍘ᒥ 鹨់ᩄ ꋔྦ 瑉浥 巠皱㙲皦抐皱 巠皱 ੨皦柘皱 ᅵ皥 ب 巠皱㙲皦忈皱 ੨皦柘皱
-
09/10/2020
Questions and Answers on Filter Technology of Compressed Air Purification System
1 Why is the most harmful of oil in the air? Answer: In some places with strict requirements, such as pneumatic control systems, a drop of oil can change the condition of the air holes. Paralyze the production line that was originally running normally and automatically.
-
06/13/2020
Central Air Conditioning Maintenance: Basic Procedure for Chiller Failure Treatment
In order to ensure the safe, efficient and economical long-term normal operation of the chiller, it is very important to discover the hidden dangers of failures as early as possible during its use. Today, the editor of Service will give you an analysis o 器2 䀀 ᅵ皥 䖒皦즠Ʋ嫜ི 㲈Ʋ 䌁皦 ᮔDž༬皧嫦ིЀ 呄ᠾ鹨់༹皧 ࠄ 00령ꐱ댁珵뛐珵Љ 䕄ྦ 뤂ᐱ뚜珵 ᴴᏩ呄ᠾ
-
08/09/2020
The harm of overheating of industrial water chiller to equipment during use
The overheating problem of industrial chillers has a serious negative impact on the efficiency of the equipment. In order to maintain the safety and stability of industrial chillers, when using industrial chillers,
-
09/06/2020
What should I do if the bearing is broken
How to judge whether the bearing can be used again and the defect that needs to be replaced To judge whether the bearing can be used again, it should be decided according to related factors such as bearing damage level, mechanical performance, importance, operating conditions, inspection period, etc.