Please click Send us the order information , we will contact you as soon as possible !
Daikin Air Conditioner FJTMP71CAP
Please click Send us the order information , we will contact you as soon as possible !
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
MINDMAN Air Cylinder MCDA-03-12-25
KCM Industrial Chain KCM 50
HAZE Battery HZB2-200
Recent related posts
-
06/14/2020
About the six advantages of the fresh air system and the four details that need attention
About the six advantages of the fresh air system and the four details that need attention With the continuous improvement of living standards, coupled with whether the haze weather is invading, the fresh air system is gradually becoming a necessary choic ﰸ2 䀀 ᅵ皥 䖒皦즠Ʋ娼ི 㲈Ʋ 䌁皦隆 ᮔDž༬皧婆ིЀ 呄ᠾ鹨់༹皧 ࠄ 00븹먱댁珵理뛐珵Љ 䕄ྦ 뤂ᐱ變뚜
-
06/14/2020
The difference between single and twin screw compressors is reflected in the following 6 aspects
The difference between single and twin screw compressors is reflected in the following 6 aspects
-
06/21/2020
The role of condensing pressure regulating valve
Condensing pressure regulating valve When the refrigeration device is running, if the condensing pressure is high, the compressor discharge temperature will rise; the compression ratio will increase; the cooling capacity will decrease; The higher the condensing pressure, the greater the above adverse effects. The high condensation pressure is mainly seen in summer. <img src="{{media url="The_role_of_condensing_pressure_regulating_valve.jpg"}}" alt="" />
-
08/05/2021
2 Causes of Your Compressor Motor Failure
A compressor is a kind of driven fluid machinery that elevates low-pressure gas to high pressure. It is the heart of the refrigeration system.
-
08/13/2020
Compressor in the industrial chiller system produces wet stroke fault and troubleshooting
In the industrial chiller system, when the compressor sucks in wet steam, frost occurs on the cylinder wall, and the suction temperature and discharge temperature drop significantly. This is the wet stroke of the compressor, commonly known as frost.
-
01/11/2021
Fifty questions about maintenance of common faults of Mitsubishi Heavy Industries air conditioners!
Fifty questions about maintenance of common faults of Mitsubishi Heavy Industries air conditioners! Fifty-questions-about-maintenance-of-common-faults-of-mitsubishi-heavy-Industries-air-conditioners Mitsubishi Heavy Industries air conditioning commo 器2 䀀 ᅵ皥 䖒皦즠Ʋ
-
06/25/2020
Why does the use of cold and air conditioning in a car increase fuel consumption because the car cannot carry a compressor
Automotive air conditioning system _ compressor power is not high Knowledge point: The principle of the "refrigeration system" of automobile air conditioners is the same as that of domestic air conditioners. Both use compressors to drive refrigerants to achieve cooling by the principle of "evaporation and heat absorption".
-
11/13/2022
How to Install an Industrial Exhaust Fan?
Factory production emits a lot of waste gas, and there are many workers gathered. For the sake of worker health and safety concerns, some exhaust fans are installed in factories to discharge exhaust gas.
-
06/22/2020
How to add air conditioning refrigerant
Turn off the power supply of the air conditioner first; if all the light leaks, then you must evacuate before adding it; find the thick tube under the outdoor unit and add fluorine from here; you need to install the pressure gauge when adding fluorine Generally, it can be stopped at about 5 pressures; the temperature needs to be turned to the lowest when turning on the machine, and observe for about half an hour.
-
06/13/2020
Screw compressor overhaul
Screw compressor overhaul Screw compressor overhaul, normal working condition of refrigeration system in operation: 1. The suction temperature of the compressor should be 5-15 ℃ higher than the evaporation temperature; 2. The discharge temperature 器2 䀀 ᅵ皥 䖒皦즠Ʋ焬क़ 㲈Ʋ 䌁皦 ᮔDž༬皧然क़Ѐ 呄ᠾ鹨់༹皧 ࠄ 00령ꐱ댁珵뛐珵Љ 䕄ྦ 뤂ᐱ뚜珵 ᴴᏩ呄ᠾ퍘ᒥ 鹨់ᩄ ꋔྦ 瑉浥 巠皱㙲皦抐皱 巠皱 ੨皦柘皱