Danfoss Compressor SH482B3ACU

09/07/2020

Ten points to judge the pros and cons of inverter products!

The technical grade of the frequency converter is gradually developed and formed. With the improvement of use requirements and the development of technology, the quality of the device, the expansion of functions, and the progress of automation technology, it will gradually advance.

06/14/2020

There is a market for air-conditioning sterilization, and innovation is helping the market pick up

Since the beginning of this year, due to the impact of the new coronary pneumonia epidemic, the development of the air-conditioning industry has been relatively difficult. With the normalization of epidemic prevention and control, and the advent of the tr器2䀀
ￜ皥
䖒皦즠Ʋ嫜ི㲈Ʋ
䌁皦
ᮔDž༬皧嫦ིЀ呄ᠾ鹨់༹皧
ࠄ
00령ꐱ댁珵뛐珵Љ
䕄ྦ￿￿뤂ᐱ뚜珵ᴴᏩ呄ᠾ퍘ᒥ鹨់ᩄꋔྦ
瑉浥巠皱㙲皦抐皱巠皱੨皦柘皱ￜ皥
ب巠皱㙲皦忈皱੨皦柘皱
즠Ʋǜ勁皦즠ƲبǜV /펔B䌁皦
ᮔDž'

08/29/2020

Six reasons and solutions for oily exhaust of screw air compressors

Failure factors of screw engine exhaust with oil 　　 Among the failures of screw compressors, the faults with oil in the exhaust are the most common. The main factors that cause the faults with oil in the exhaust are:

08/03/2025

What Causes AC Compressor Failure and How to Prevent It? (11 Reasons＆4 Ways)

The AC compressor is an essential component of an air conditioning system, responsible for compressing and circulating refrigerant that cools down the air.

06/29/2020

Several causes of compressor burning

06/14/2020

Classification of air conditioner

Classification of air conditioner Classification of air conditioner 1. According to the purpose of use, which types of air conditioners can be divided? Comfortable air conditioning: It requires a suitable temperature and a comfortable environment, 器2䀀
ￜ皥
䖒皦즠Ʋ焬क़㲈Ʋ
䌁皦
ᮔDž༬皧然क़Ѐ呄ᠾ鹨់༹皧
ࠄ
00령ꐱ댁珵뛐珵Љ
䕄ྦ￿￿뤂ᐱ뚜珵ᴴᏩ呄ᠾ퍘ᒥ鹨់ᩄꋔྦ
瑉浥巠皱㙲皦抐皱巠皱੨皦柘皱ￜ皥
ب巠皱㙲皦

09/09/2020

The influence of machining on fatigue life

The residual compressive stress introduced by shot blasting/shot peening is a percentage of the final tensile stress strength, and this ratio increases as the strength/hardness of the part material itself increases. High-strength/hardness metals are more brittle and more sensitive to surface defects. Shot blasting/shot peening will allow these high-strength metals to be used in fatigue-prone working conditions. Aircraft landing gear is usually designed with a fatigue strength of 300 ksi (2068 MPa), combined with shot blasting/shot peening.

08/18/2020

How to maintain the cooling tower

1. Replacement of fillers. Inferior fillers have weak rigidity, poor load-bearing capacity, and are easy to deform and fall loose, which will directly lead to poor cooling effect or loss of cooling capacity.

09/06/2020

Application of synthetic compressor oil

At present, synthetic lubricants are widely used in the compressor field. Among them, oil-injected and oil-immersed rotary screw air compressors and large reciprocating compressors are one of the most used markets. For example, the sales volume of synthetic compressor oil in Western Europe was 6000t in the late 1980s, and it rose to 10000 in the early 1990s. The sales volume in the United States has exceeded 15,000 tons, and it is increasing at a rate of more than 10% per year.

06/14/2020

How to judge the quality of single-phase and three-phase refrigeration compressors

A compressor is a driven fluid machine that raises low-pressure gas to high-pressure gas, and is the heart of a refrigeration system. Then, after-sales maintenance sometimes doubts that the compressor is malfunctioning, how to check and judge at this time器2䀀
ￜ皥
䖒皦즠Ʋ煔क़㲈Ʋ
䌁皦
ᮔDž༬皧煞क़Ѐ呄ᠾ鹨់༹皧
ࠄ
00령ꐱ댁珵뛐珵Љ
䕄ྦ￿￿뤂ᐱ뚜珵ᴴᏩ呄ᠾ퍘ᒥ鹨់ᩄꋔྦ
瑉浥巠皱㙲皦抐皱巠皱੨皦柘皱ￜ皥