Shaft diameter:6mm
Interface and power supply:Push-pull HTL (with inverted signal), 5-30Vdc Way out:Metal fixed head output cable length 0.5m (IP66) Outbound direction:Radial
Single circle resolution:1024
ELCO Encoder EC40A6-H4PR-1024
People who bought this item also viewed
Lika Encoder CK58-H-1024ZCU415
HENGSTLER Encoder AC36/1212AR.41SBA
LS Mecapion Encoder H40-8-0100VL
SIEMENS Servo Motor 1FK7032-5AK71-1TA0
ABB Servo Drive 3HAC14546-6
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
KSK Oil SealTC(FKM)28X45X10
SMC Solenoid Valve SY3220-5MOZ-M5
KOA Fuse TF16SN2.00TTD
SHAKO Air Cylinder JC63B70-H
AirTAC Air Cylinder HLQ16X100-S
GMCC Compressor DA108M1C-81EZ8
Recent related posts
-
09/15/2020
83 river water level transmitter, diffused silicon piezoresistive core sensor
83 river water level transmitter, diffused silicon piezoresistive core sensor, Guangdong pressure sensor, Foshan pressure transmitter, Shunde pressure sensor PTH601 uses diffused silicon piezoresistive core or ceramic piezoresistive core, 316 stainless steel structure, mainly suitable for rivers, groundwater levels, reservoirs, water towers and containers, etc. liquid level measurement and control.
-
04/20/2022
What is A Level Transmitter?
Level transmitter is the extension and development of pressure transmitter technology. It realizes the accurate measurement and transmission of the volume, liquid height and weight of water
-
08/13/2020
How to deal with the high pressure overload of the chiller
When the condenser heat dissipation is poor, the compressor efficiency is low and the operating current increases. When the high pressure rises to 19Kg/cm2, the compressor trips under the protection of the high pressure switch and the compressor stops runPﰨ2
-
06/19/2020
What are the causes of air conditioning trip
What are the causes of air conditioning trip 1. The contradiction between the rated current of the air conditioner and the current carrying capacity of the wire. Here are two formulas involved: ①The rated current of air conditioner I=P÷U ÷power factor, the power remains unchanged, the smaller the voltage, the greater the current required. ② The current carrying capacity of the wire I=U÷R, the voltage is proportional to the current. So when the power supply voltage is normal, we must consider the line voltage drop. The longer the line, the greater the resistance, the greater the voltage drop, and the smaller the output current at the end. However, because the power of the load remains unchanged, the voltage becomes smaller, and the current that needs to be output will be larger. At this time, the wire is forced to overload, and the time will cause heating, and eventually cause the tripping of the open circuit. Some friends said that the heat of the wire will not cause the tripping of the circuit breaker. In fact, the manufacturer of the air switch has made it clear in the relevant manuals that the heat of the wire will cause the air switch to trip. Because the wire heats up, the crimp terminal will also heat up, and the resistance will become larger and larger. The larger the resistance, the greater the current consumption, and the hotter it will be, a vicious cycle. 2. Leakage During the daily maintenance work, we will encounter the situation that the air circuit trips due to the leakage of electricity. At least I have not experienced it once or twice. Regardless of the leakage of the neutral line or the leakage of the live line, a long time will cause the circuit breaker to trip. Why does the electric leakage cause the MCB to trip? There are two situations. ① Good grounding. At the beginning, the leakage current was not large, and as time went by, the leakage current became larger and larger, and eventually evolved into a short circuit to ground, unable to close. ②There is no ground wire. If the equipment is not connected to the protective ground, when the wire leaks to the equipment, it is equivalent to adding a large shunt resistance. Like this problem, if the air conditioner does not have a ground wire, when the wire leaks to the air conditioner, the air conditioner is a very large shunt resistor and will consume a lot of current. Eventually, the wire will heat up or trip open. How to determine whether the trip caused by the above two aspects can be done with a clamp ammeter. ① Measure the voltage at the input and output to see if there is a significant change in voltage drop. ②Measure whether the output current exceeds the standard. So my suggestion is: first measure the supply voltage to see if it is within the allowable fluctuation range. Then measure the current to see if it exceeds the rated ampacity of the wire. Finally, check the data one by one according to the measured data to find out the reason.
-
06/26/2020
Analysis of common faults and solutions of air-conditioning compressors
The air conditioning compressor is the heart of the refrigeration system and the power source for the refrigerant to circulate in the system. The basic working principle of the refrigeration system mainly includes the four processes of compression, condensation, throttling and evaporation.
-
04/09/2024
9 American Servo Motor Manufacturers
The following introduces the relatively famous servo motor manufacturers in the United States. Hope it will be helpful for you to understand the servo motor brands and servo product selection.
-
11/02/2022
Pros and Cons of 4 Pairs of Electric Motors
According to different structures, working principles, types of operating power, and uses, electric motors can be divided into various types.
-
06/13/2020
Single screw compressor
Single screw compressor
-
07/02/2020
Several reasons why the American Taikang compressor meets China's national conditions
Several reasons why the American Taikang compressor meets China's national conditions In this era, as the Chinese people's vision is getting higher and higher, even imports must meet a condition in order to gain a long-term foothold in the Chinese market. This prerequisite is in line with China's national conditions.
-
07/16/2020
How to see if the refrigerant leaks in the high and low temperature test chamber
How to check whether the refrigerant leaks in the high and low temperature test box; the standard high and low temperature test box and the constant temperature and humidity test box are all selected by the air-cooled compressor, and the working principle is the same as that of the air conditioning refrigeration