Sensing range 2 mm flush mountable
normally open
DC PNP
M12 Connector
IFM Sensor IEC200
People who bought this item also viewed
IFM Sensor IGS312
IFM Sensor IT5040
IFM Sensor PI2798
IFM Sensor PI1698
Keyence Sensor OP-75722
Contrinex Sensor LTS-5050-104
Honeywell Sensor 060-F508-01
Dwyer Transmitter WHT-333
Riello Flame Detector KLC1000
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
JSCC Speed Reducer 90GF60H
SMC Solenoid Valve VP542R-5G-03-X20
NORGREN Filter 5576-01
PARKER Filter G02815
IXYS Relay CPC1106N
Recent related posts
-
08/04/2021
Mitsubishi Vs. Panasonic Air Conditioners
Summer is so difficult to spend that people without the air conditioner are like fish out of water. It’s critical to choose a good air conditioner.
-
09/06/2020
Application of Frequency Conversion in Oilfield Development and Energy Saving
The application of frequency conversion energy saving in the crude oil extraction industry is mainly manifested in various pumps. In order to ensure the reliability of production, all kinds of production machinery have a certain margin when they are designed and equipped with power drives.
-
06/20/2020
What are the causes of air conditioning trip
What are the causes of air conditioning trip 1. The contradiction between the rated current of the air conditioner and the current carrying capacity of the wire. Here are two formulas involved: ①The rated current of air conditioner I=P÷U ÷power factor, the power remains unchanged, the smaller the voltage, the greater the current required. ② The current carrying capacity of the wire I=U÷R, the voltage is proportional to the current. So when the power supply voltage is normal, we must consider the line voltage drop. The longer the line, the greater the resistance, the greater the voltage drop, and the smaller the output current at the end. However, because the power of the load remains unchanged, the voltage becomes smaller, and the current that needs to be output will be larger. At this time, the wire is forced to overload, and the time will cause heating, and eventually cause the tripping of the open circuit. Some friends said that the heat of the wire will not cause the tripping of the circuit breaker. In fact, the manufacturer of the air switch has made it clear in the relevant manuals that the heat of the wire will cause the air switch to trip. Because the wire heats up, the crimp terminal will also heat up, and the resistance will become larger and larger. The larger the resistance, the greater the current consumption, and the hotter it will be, a vicious cycle. 2. Leakage During the daily maintenance work, we will encounter the situation that the air circuit trips due to the leakage of electricity. At least I have not experienced it once or twice. Regardless of the leakage of the neutral line or the leakage of the live line, a long time will cause the circuit breaker to trip. Why does the electric leakage cause the MCB to trip? There are two situations. ① Good grounding. At the beginning, the leakage current was not large, and as time went by, the leakage current became larger and larger, and eventually evolved into a short circuit to ground, unable to close. ②There is no ground wire. If the equipment is not connected to the protective ground, when the wire leaks to the equipment, it is equivalent to adding a large shunt resistance. Like this problem, if the air conditioner does not have a ground wire, when the wire leaks to the air conditioner, the air conditioner is a very large shunt resistor and will consume a lot of current. Eventually, the wire will heat up or trip open. How to determine whether the trip caused by the above two aspects can be done with a clamp ammeter. ① Measure the voltage at the input and output to see if there is a significant change in voltage drop. ②Measure whether the output current exceeds the standard. So my suggestion is: first measure the supply voltage to see if it is within the allowable fluctuation range. Then measure the current to see if it exceeds the rated ampacity of the wire. Finally, check the data one by one according to the measured data to find out the reason.
-
08/18/2020
How to wire the cold storage distribution box What problems should be paid attention to when wiring
Cold storage power distribution boxes play a very important role in the use of cold storage, and many people do not know much about cold storage power distribution boxes. Let's take a look at it with okmarts.com editor.
-
09/07/2020
How to save energy in the dryer in the compressed air purification system
In many industrial occasions, compressed air systems have very high requirements for the water content of compressed air, such as: chemical, pharmaceutical, spraying, power electronics and other industries;
-
09/01/2022
What is a Magnetic Contactor?
In many cases, the magnetic contactor is simply referred to as a contactor. It is an electrical appliance that uses the current flowing through the coil to generate a magnetic field to close the contacts to control the load in industrial electricity.
-
08/25/2020
Cold pipe refrigeration system only half the power of the air conditioner
On August 19, according to foreign media reports, a new study from the Proceedings of the National Academy of Sciences demonstrated a new energy-saving refrigeration system that only needs half the electricity of the air conditioner.
-
09/04/2020
Analysis of the advantages and disadvantages of 5 types of compressors
There are mainly 5 types of compressors, piston compressors, rolling rotor compressors, turbo compressors, screw compressors, and centrifugal compressors. This article briefly introduces the advantages and disadvantages of various compressors.
-
03/18/2021
Summary of the key issues of the servo motor drive
According to the current of the motor, use a driver that is greater than or equal to this current. If low vibration or high precision is required, a subdivision drive can be used. For high-torque motors, use high-voltage drivers as much as possible to obtain good high-speed performance.
-
06/14/2020
Haikou exploded, the central air conditioner was back
Haikou exploded, the central air conditioner was back, was it wrong Since 2020, the safety of the use of central air conditioning has been widely concerned. From the clustered infections in closed places during the epidemic to the explosion accident in H 器2 䀀 ᅵ皥 䖒皦즠Ʋ煔क़ 㲈Ʋ 䌁皦 ᮔDž༬皧煞क़Ѐ 呄ᠾ鹨់༹皧 ࠄ 00령ꐱ댁珵뛐珵Љ 䕄ྦ 뤂ᐱ뚜珵 ᴴᏩ呄ᠾ퍘ᒥ 鹨់ᩄ ꋔྦ 瑉浥 巠皱