AC1: 135A
AC3
200/240V: 25kW 85A
380/440V: 45kW 85A
500/550V: 45kW 75A
690V: 45kW 45A
LG LS Contactor MC-85A
People who bought this item also viewed
LG LS Contactor GMC-20P2
AEG Contactor SH8-44E
RIKEN Contactor RAB-A24
Nader Contactor NDC1-225
AEG Contactor MC2C310AT
CHINT Transformer JBK1-400
Merlin Gerin Circuit Breaker M08H1 3P STR38S
OBO Surge Protection Device MC 125-B NPE
Littelfuse Fuse BLN001
TYCO Relay C93402
Yageo Resistor MF0207FTE52-3R9
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
SAMYOUNG Capacitor 400V 1000UF
Siemens Circuit Breaker 5SY7216-8MA
PIZZATO Switch FR 1393-D5M2
Siemens Contactor 3TF6833-1QL7
Recent related posts
-
11/13/2022
How to Install an Industrial Exhaust Fan?
Factory production emits a lot of waste gas, and there are many workers gathered. For the sake of worker health and safety concerns, some exhaust fans are installed in factories to discharge exhaust gas.
-
06/14/2020
What are the causes of frost in refrigeration compressors
1. The opening of the thermal expansion valve is too large, or the installation of the temperature sensor is incorrect and the fixing is not firm or loose. The main reason is that the temperature sensor may feel the temperature too high in this case, resu 器2 䀀 ᅵ皥 䖒皦즠Ʋ奌ི 㲈Ʋ 䌁皦 ᮔDž
-
08/13/2020
How to replace the lubricating oil and filter drier of the chiller
After the chiller is used for a long time, the lubricating oil will inevitably be contaminated or acidified. Therefore, we must pay attention to the change of oil quality during the operation of the unit.
-
03/16/2021
How to maintain the servo motor driver?
In order to prolong the lifespanof the servo system, you should pay attention to the following aspects. For the operating environment of the system, the temperature, humidity, dust, vibration and input voltage need to be considered. Please regularly clean the ventilation system of the numerical control device. Always check whether the cooling fans on the numerical control device are working properly. It should be inspected and cleaned every six months or a quarter depending on the environment of the workshop.
-
07/10/2022
6 Reasons for Why Mechanical Seals Fail
You might be asking yourself, why are my seals failing so fast, and how can I prevent this from happening? This topic rings true among operators and engineers in plants of all sizes and industries.
-
07/27/2020
The working principle of screw unit and common failure analysis
1. Refrigeration cycle and pressure enthalpy diagram<br></br> The refrigeration cycle of a screw chiller can be represented by a pressure-enthalpy diagram. The main state points are shown in the diagram, which will be used in the following discussion.
-
07/16/2020
Three factors determine the quality of cold storage
The size of the cold storage should be designed according to the highest amount of agricultural products to be stored throughout the year. This capacity is calculated based on the volume that the stored products must occupy in the cold storage, plus the aisles between the rows, the space between the stack and the wall and ceiling, and the gap between the packaging.
-
12/07/2022
The Lubrication of the Linear Guideway
For the sake of better performance, smaller wear, and longer service life of the linear guideway, proper lubrication is entailed. This article will discuss the functions, characteristics of lubricant and tips for lubrication.
-
09/04/2020
Analysis of the advantages and disadvantages of 5 types of compressors
There are mainly 5 types of compressors, piston compressors, rolling rotor compressors, turbo compressors, screw compressors, and centrifugal compressors. This article briefly introduces the advantages and disadvantages of various compressors.
-
08/03/2020
Five classification functions of cold storage installation cold storage function
The refrigerated distribution center is developed based on the two needs of the rationalization of refrigerated logistics and the development of the market.