Repeatability: ±0.15% full scale or better
Turndown Ratio: 100:1
Response Time: 5 seconds
Gas Ambient Temperature: 0 to 50°C (32 to 122°F)
Temperature Coefficient: 0.05% full scale per 1°C or better
Pressure Coefficient: 0.01% full scale per psi or better
Minimum Pressure Requirements:
Meters: 1 inch of H2O
Controllers ≤1 SLM: 1 psi
Controllers >20 SLM: 20 psi
Differential Pressure for Mass Flow Controllers:
<5 LPM: 5 to 50 psi standard
>5 LPM: 20 to 40 psi standard
Maximum Gas Pressure:
Polyacetal: 250 psig
316 SS: 500 psig
Leak Integrity: 1 x10-6 cc/min of He or better
Wetted Parts:
Standard: Polyacetal, FKM O-rings
Optional: 316 SS, FKM O-rings
Connections: 1/4 FNPT standard; 1/4' compression fitting for all stainless steel models
Input/Output Connection: 9-pin sub-D connector
Control Signal: 0 to 5 Vdc
Control Valve: Electromagnetic normally closed
Output signal: Linear 0 to 5 Vdc, 1000 Ω min load, 4 to 20 mA, 500 Ω loop resistance
Input Power:
Meters: 24 Vdc @ 150 mA, 115 Vac, 220 Vac with AC adaptor
Controller: 24 Vdc @ 300 mA, 115 Vac, 220 Vac with AC adaptor
Dimensions: See drawing
Weight: 1.25 kg (2.75 lb) with power supply
Omega Flowmeter FMA-A2104
People who bought this item also viewed
YOKOGAWA Flowmeter AXFC-4-L010/CH
BDSENSORS Level Meter DAP200
WTW Turbidity Meter Turb 430 IR
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
Balluff Sensor BGL000T
Sanken VFD Frequency Converter S06-4A014-B
Recent related posts
-
08/15/2020
Precautions during the use of air-cooled refrigerators
Before using the air-cooled chiller, you can carefully count the operating data of the equipment, and then based on these operating data, you can make a basic judgment on the operating status of the equipment,
-
08/10/2020
Precautions for the use of refrigeration compressor overload protector
Overload protectors for compressors used in air conditioners generally use snap-on bimetallic protectors, consisting of a heating wire, a bimetallic sheet and two static contacts, which are connected in series in the compressor circuit.
-
09/30/2022
Three Control Methods of Servo Motor
There are three types of <strong>servo motor control</strong> modes (<strong>servo motor control techniques</strong>)
-
12/07/2021
How Does a Refrigeration Compressor Work? With Animation for Each Type
Refrigeration compressor is a kind of driven fluid machinery, which promotes low-pressure gas to high-pressure gas and is the heart of refrigeration system.
-
07/20/2020
How to judge the starter of the refrigerator compressor is broken
1. The heavy hammer starter, the part that is easily damaged is the poor contact of the start contact. During the measurement, the weight starter can be removed and measured with a multimeter ohm block according to the original installation direction.
-
06/13/2020
How does the central air conditioning screw compressor replace the freezing oil
Refrigerating oil, also known as lubricating oil, is mainly used for lubricating various moving parts in refrigeration compressors. It belongs to refrigeration consumable products. So, how does the central air conditioning screw compressor replace the fre ﰸ2 䀀 ᅵ皥 䖒皦즠Ʋ娼ི 㲈Ʋ 䌁皦隆 ᮔDž༬皧婆ིЀ 呄ᠾ鹨់༹皧 ࠄ
-
01/26/2022
A Quick Look at the Submersible Pressure Transmitter
Submersible pressure transmitters use imported chip assembly, reflecting the superior technology. Their structure is compact and firm and is light for installation.
-
06/13/2023
Refrigerator Compressor Not Running and What to Do?
When it comes to refrigeration, the compressor is one of the most crucial components. It plays a vital role in keeping your refrigerator running, as it's responsible for pumping refrigerant throughout the system.
-
09/09/2020
The influence of machining on fatigue life
The residual compressive stress introduced by shot blasting/shot peening is a percentage of the final tensile stress strength, and this ratio increases as the strength/hardness of the part material itself increases. High-strength/hardness metals are more brittle and more sensitive to surface defects. Shot blasting/shot peening will allow these high-strength metals to be used in fatigue-prone working conditions. Aircraft landing gear is usually designed with a fatigue strength of 300 ksi (2068 MPa), combined with shot blasting/shot peening.
-
03/14/2022
6 Things about the Ammonia Refrigeration Compressor Maintenance
In the refrigeration system of the cold storage, the refrigeration compressor is the core equipment.