Pan-globe Temperature Controller K904-04000020110

09/09/2020

Industrial bearing knowledge

Structural features 　　Bearing seat: The bearing seat is made of cast iron with heat sink on the surface. The mating surface of the bearing seat and the bearing bush is spherical. Bearing seats are divided into two types: insulated and non-insulated.

01/18/2024

Difference between Industrial Axial and Centrifugal Fans

Fan are widely used in factories, mines, tunnels, cooling towers, vehicles, ships, buildings and other fields for ventilation, dust removal and cooling fluid machinery.

06/29/2020

Compression ratio of American Copeland compressor

08/18/2020

How to effectively heat the roof of cold storage

In order to reduce the influence of outdoor air temperature on the interior, the cold storage roof must be insulated. Currently, there are usually the following two approaches.

08/18/2020

Reasons for the high low pressure value of the chiller

In the application of industrial refrigeration, the chiller is used in conjunction with production and processing equipment, so it runs for a long time. If the customer lacks professional maintenance and routine equipment maintenance for the chiller in daily life

08/14/2020

Factors affecting the boiling heat transfer of refrigerant liquid

In the evaporator, the heat of the cooled medium is transferred to the refrigerant through the heat transfer wall, so that the liquid refrigerant absorbs heat and vaporizes.

09/09/2020

The influence of machining on fatigue life

The residual compressive stress introduced by shot blasting/shot peening is a percentage of the final tensile stress strength, and this ratio increases as the strength/hardness of the part material itself increases. High-strength/hardness metals are more brittle and more sensitive to surface defects. Shot blasting/shot peening will allow these high-strength metals to be used in fatigue-prone working conditions. Aircraft landing gear is usually designed with a fatigue strength of 300 ksi (2068 MPa), combined with shot blasting/shot peening.

06/20/2020

What are the causes of air conditioning trip

What are the causes of air conditioning trip 1. The contradiction between the rated current of the air conditioner and the current carrying capacity of the wire. 　　Here are two formulas involved: 　　①The rated current of air conditioner I=P÷U ÷power factor, the power remains unchanged, the smaller the voltage, the greater the current required. 　　② The current carrying capacity of the wire I=U÷R, the voltage is proportional to the current. 　　 So when the power supply voltage is normal, we must consider the line voltage drop. The longer the line, the greater the resistance, the greater the voltage drop, and the smaller the output current at the end. However, because the power of the load remains unchanged, the voltage becomes smaller, and the current that needs to be output will be larger. At this time, the wire is forced to overload, and the time will cause heating, and eventually cause the tripping of the open circuit. 　　 Some friends said that the heat of the wire will not cause the tripping of the circuit breaker. In fact, the manufacturer of the air switch has made it clear in the relevant manuals that the heat of the wire will cause the air switch to trip. Because the wire heats up, the crimp terminal will also heat up, and the resistance will become larger and larger. The larger the resistance, the greater the current consumption, and the hotter it will be, a vicious cycle. 　　 2. Leakage 　　During the daily maintenance work, we will encounter the situation that the air circuit trips due to the leakage of electricity. At least I have not experienced it once or twice. Regardless of the leakage of the neutral line or the leakage of the live line, a long time will cause the circuit breaker to trip. 　　Why does the electric leakage cause the MCB to trip? There are two situations. 　　 ① Good grounding. At the beginning, the leakage current was not large, and as time went by, the leakage current became larger and larger, and eventually evolved into a short circuit to ground, unable to close. 　　②There is no ground wire. If the equipment is not connected to the protective ground, when the wire leaks to the equipment, it is equivalent to adding a large shunt resistance. Like this problem, if the air conditioner does not have a ground wire, when the wire leaks to the air conditioner, the air conditioner is a very large shunt resistor and will consume a lot of current. Eventually, the wire will heat up or trip open. 　　How to determine whether the trip caused by the above two aspects can be done with a clamp ammeter. 　　 ① Measure the voltage at the input and output to see if there is a significant change in voltage drop. 　　②Measure whether the output current exceeds the standard. 　　 So my suggestion is: first measure the supply voltage to see if it is within the allowable fluctuation range. Then measure the current to see if it exceeds the rated ampacity of the wire. Finally, check the data one by one according to the measured data to find out the reason.

06/14/2020

How to choose the matching type of cold storage

A, high temperature cold storage (± 5 ℃): suitable for the preservation of fruits and vegetables; B. Medium temperature cold storage (-10 ℃ ~ -5 ℃): suitable for food refrigeration after freezing; C, low temperature cold storage (-20 ℃ ~ -10 ℃): sui器2䀀
ￜ皥
䖒皦즠Ʋ奌ི㲈Ʋ
䌁皦
ᮔDž༬皧奖ིЀ呄ᠾ鹨់༹皧
ࠄ
00령ꐱ댁珵뛐珵Љ
䕄ྦ￿￿뤂ᐱ뚜珵ᴴᏩ呄ᠾ퍘ᒥ鹨់ᩄꋔྦ
瑉浥巠皱㙲皦抐皱巠皱੨皦柘皱ￜ皥
ب巠皱㙲皦忈皱੨皦柘

07/17/2020

How to tell the authenticity of Emerson semi-closed Copeland compressor

How to tell the authenticity of Emerson semi-closed Copeland compressor In the market, there are customers who reflect that they are buying fake Emerson semi-closed Copeland compressors. Here, in order to allow customers to better identify the authenticity of Emerson semi-closed Copeland compressors, they freeze in Emerson Environmental Optimization Technology (Shenyang) Machinery Co., Ltd.