Sanyo Compressor C-SBP120H33F

06/29/2020

What is the cause of compressor pipeline vibration

03/01/2021

Performance comparison between servo motor and stepping motor

As an open-loop control system, stepping motor has essential connection with modern digital control technology. In the current domestic digital control system, stepping motor is widely used. With the emergence of all digital AC servo system, AC servo motor is more and more used in digital control system. In order to adapt to the development trend of digital control, stepping motor or full digital AC servo motor is mostly used as the executive motor in motion control system. Although they are similar in control mode (pulse train and direction signal), they are quite different in performance and application. This paper compares the performance of the two.

06/24/2024

Top 11 Hydraulic Solenoid Valve Manufacturers Worldwide

The hydraulic solenoid valve is a widely used valve product and there are many brands/manufacturers of hydraulic solenoid valves on the market.

06/20/2020

What are the causes of air conditioning trip

What are the causes of air conditioning trip 1. The contradiction between the rated current of the air conditioner and the current carrying capacity of the wire. 　　Here are two formulas involved: 　　①The rated current of air conditioner I=P÷U ÷power factor, the power remains unchanged, the smaller the voltage, the greater the current required. 　　② The current carrying capacity of the wire I=U÷R, the voltage is proportional to the current. 　　 So when the power supply voltage is normal, we must consider the line voltage drop. The longer the line, the greater the resistance, the greater the voltage drop, and the smaller the output current at the end. However, because the power of the load remains unchanged, the voltage becomes smaller, and the current that needs to be output will be larger. At this time, the wire is forced to overload, and the time will cause heating, and eventually cause the tripping of the open circuit. 　　 Some friends said that the heat of the wire will not cause the tripping of the circuit breaker. In fact, the manufacturer of the air switch has made it clear in the relevant manuals that the heat of the wire will cause the air switch to trip. Because the wire heats up, the crimp terminal will also heat up, and the resistance will become larger and larger. The larger the resistance, the greater the current consumption, and the hotter it will be, a vicious cycle. 　　 2. Leakage 　　During the daily maintenance work, we will encounter the situation that the air circuit trips due to the leakage of electricity. At least I have not experienced it once or twice. Regardless of the leakage of the neutral line or the leakage of the live line, a long time will cause the circuit breaker to trip. 　　Why does the electric leakage cause the MCB to trip? There are two situations. 　　 ① Good grounding. At the beginning, the leakage current was not large, and as time went by, the leakage current became larger and larger, and eventually evolved into a short circuit to ground, unable to close. 　　②There is no ground wire. If the equipment is not connected to the protective ground, when the wire leaks to the equipment, it is equivalent to adding a large shunt resistance. Like this problem, if the air conditioner does not have a ground wire, when the wire leaks to the air conditioner, the air conditioner is a very large shunt resistor and will consume a lot of current. Eventually, the wire will heat up or trip open. 　　How to determine whether the trip caused by the above two aspects can be done with a clamp ammeter. 　　 ① Measure the voltage at the input and output to see if there is a significant change in voltage drop. 　　②Measure whether the output current exceeds the standard. 　　 So my suggestion is: first measure the supply voltage to see if it is within the allowable fluctuation range. Then measure the current to see if it exceeds the rated ampacity of the wire. Finally, check the data one by one according to the measured data to find out the reason.

08/17/2020

How to recover refrigerant

1. How to recover the refrigerant from the industrial chiller to the accumulator? 　　The specific operation steps for recovering the refrigerant from the industrial chiller to the accumulator are:

08/13/2020

What are the thermal state parameters of the refrigerant

In the refrigeration cycle, the working fluid continuously changes its thermal state. The physical quantity describing the thermal state of the working fluid is called the thermal state parameter of the working fluid

08/02/2020

Those human factors that cause damage to the refrigeration compressor

This article mainly introduces the phenomenon of the refrigeration compressor burned out due to the loose wiring and the incorrect placement of the temperature sensor and the specific treatment methods. Knowing and preventing is the meaning of knowing

08/15/2020

How to achieve low-cost operation of the freezer

Enterprise users who use refrigerators are more concerned about the cost of use. The editor of okmarts.com believes that only by saving energy can the cost of enterprise use be effectively saved.

03/10/2025

Top 13 Servo Motor Manufacturers Worldwide in 2024

There are many brands of servo motors on the market. How can you choose a cost-effective brand with good quality among the many brands?

06/14/2020

Technical status and development trend of refrigeration and air-conditioning compressors

Refrigeration machinery and air conditioning equipment play a very important role in the development of the national economy, the improvement of people's lives and the support of national defense equipment.