SILERGY Integrated Circuit Chip SY7104DBC
- Specifications
- Q&A
- Reviews
LG LS PLC AC I/O hybrid module G4H-DT2A
DIEWU NIC Card 82575-1X
Fanuc I/O Module A03B-0819-C109
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
OPTICON Scanner OPH-1005
SCHMERSAL Switch TV1H236-11Z-M20
SCHMERSAL Switch M697-11-1
09/04/2020
Soft starter concept Soft start (also known as soft starter, motor soft starter, soft starter) Soft start is a novel motor control device that integrates motor soft start, soft stop, light load energy saving and multiple protection functions.
06/14/2020
Piston screw scroll centrifuge compressor characteristics analysis 1. Semi-closed piston compressor Principle: Rely on the reciprocating motion of the piston to compress the gas in the cylinder.
07/16/2020
Overload protector of air conditioner compressor Installed between the active and passive sides of the power transmission, when an overload fault occurs (torque exceeds the set value), the torque limiter will separate, thereby effectively protecting the driving machinery and the load. Just like its name, the fundamental function of the overload protector is to protect the air-conditioning compressor.
06/14/2020
What to do if the refrigeration compressor is damaged After the refrigeration compressor in the refrigeration system is damaged, the new compressor cannot be replaced directly because there may be some incentives for the refrigeration compressor to be da 器2 䀀 ᅵ皥 䖒皦즠Ʋ嫜ི 㲈Ʋ 䌁皦 ᮔDž༬皧嫦ིЀ 呄ᠾ鹨់༹皧 ࠄ 00령
08/15/2020
Industrial chillers are commonly used temperature control equipment and are used in various industries. Therefore, the requirements for use are also different. The requirements for laser and
07/22/2020
Freon refrigerants are generally used in cold storage refrigeration systems, so the following is a brief introduction to some of the operating specifications of Freon refrigeration units, so that everyone will feel very simple and relaxed when using them.
01/05/2021
Compressor: Of the reciprocating, rotary, and centrifugal compressors, the most popular among domestic or smaller power commercial refrigeration is the reciprocating. The reciprocating compressor is similar to an automobile engine. A piston is driven by a 器2 䀀 ᅵ皥 䖒皦즠Ʋ㎄ᰙ 㲈Ʋ 䌁皦 ᮔDž༬皧㎎ᰙЀ 呄ᠾ鹨់༹皧 ࠄ 00령ꐱ댁珵뛐珵Љ 䕄ྦ 뤂ᐱ뚜珵 ᴴᏩ呄ᠾ퍘ᒥ 鹨់ᩄ ꋔྦ 瑉浥 巠皱㙲皦抐皱 巠皱 ੨皦柘皱 ᅵ皥 ب 巠皱㙲皦忈皱 ੨皦柘皱 즠Ʋǜ 勁皦즠Ʋب ǜ V / 펔B䌁皦 ᮔDž '鱤džၜ먢䇨珵呈ᠾ뤂ᐱ ⿇⬿먲僧ᐱ㥲ᐲ�僬㣢ᐲ ᠾ 랖僧۲ 識 �僬㣢ᐲ 臆S㥲ᐲ ᬄğ 識 理艏S杴 識杴 㥲ᐲ
06/23/2020
1.The air conditioner remote control may not adjust the temperature. 2. It may be that the air conditioner has not been cleaned for too long, which causes dust to accumulate on the filter net, so that the cold air blocking the air conditioner cannot be blown out. 3. There may be leakage of freon in the air conditioner, resulting in too little freon, and the air conditioner is not cooled. 4. Energy saving is due to unstable voltage, which causes the air conditioner to not be cooled. 5. It may be that the number of air conditioners is insufficient, and the small number of horses is not used for cooling in a large area of the house.
09/23/2020
1. Design intent For cost reasons, the control systems used in the air compressor manufacturing industry for a long time have been controlled by single-chip microcomputers, and digital tubes indicate working status and indicate parameter values
09/09/2020
The residual compressive stress introduced by shot blasting/shot peening is a percentage of the final tensile stress strength, and this ratio increases as the strength/hardness of the part material itself increases. High-strength/hardness metals are more brittle and more sensitive to surface defects. Shot blasting/shot peening will allow these high-strength metals to be used in fatigue-prone working conditions. Aircraft landing gear is usually designed with a fatigue strength of 300 ksi (2068 MPa), combined with shot blasting/shot peening.