Maximum flow:120 L/min
Adjustment - No. of CW Turns from Min. to Max. setting:5
SUN Overflow Valve RVEA-LWN
People who bought this item also viewed
REXROTH Overflow Valve DBDS8H1X/315
KOMPASS Check Valve MSC-02B-A220
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
Daikin Piston Pump V23A4RX-95
BECKER FAN SV7.190/2-01 THREE PHASE
Bristol Compressor H21J383ABC
PHLE Oil Seal 2.750-3.500-0.500
Recent related posts
-
08/14/2020
How does the cold storage refrigeration system supplement and discharge refrigerant
The cold storage refrigeration system must ensure that the refrigerant is dry when adding refrigerant (only applicable to fluorine refrigerant refrigeration systems),
-
08/14/2020
How to reduce the overall cost of purchasing industrial chillers
How to reduce the overall cost of purchasing industrial chillers
-
01/11/2024
Common Faults of Cold Storage (with a List of Fault Repair Methods)
Cold storage is an indispensable and important facility in many industries. They play a key role in storing and preserving various products. However, even with the most sophisticated systems, cold storage can suffer from various failures.
-
09/20/2020
What are mineral oil, semi-synthetic oil and fully synthetic oil What is the difference between them
Mineral oil (MineralLubricant) Mineral oil is a lubricating oil extracted from petroleum. The base oil of mineral oil is the bottom oil left over after the fractional distillation of useful light substances (such as aviation oil, gasoline, etc.) during crude oil refining. Into the product. Essentially, it uses the poorer components of crude oil. Mineral oil is currently the most common type of lubricant on the market.
-
07/07/2020
How much do you know about the diameter of the refrigeration system and the return of the upstream pipe
How much do you know about the diameter of the refrigeration system and the return of the upstream pipe When the refrigeration equipment is under low load, if it is found that the oil return cannot be normal, it can be calculated according to the minimum return oil flow rate.
-
07/04/2020
The compressor lacks oil, so the harm is so great!
The compressor lacks oil, so the harm is so great! Compressors are complex machines that operate at high speeds. Ensuring adequate lubrication of moving parts such as compressor crankshafts, bearings, connecting rods, and pistons is the basic requirement for maintaining normal operation of the machine.
-
09/05/2020
What are the energy saving methods for air compressor systems
Facing the challenges of global climate change and environmental ecology, countries and industries in the world are actively taking action to find a way for energy-saving development.
-
01/12/2021
Which air conditioner is better for Daikin and Mitsubishi Electric?
Which air conditioner is better for Daikin and Mitsubishi Electric? Four major pieces of air conditioner, compressor, condenser, evaporator, throttling device, and finally, fighting for technology, fighting for capital Technically speaking, it is the 器2 䀀 ᅵ皥 䖒皦즠Ʋ㎄ᰙ 㲈Ʋ 䌁皦 ᮔDž༬皧㎎ᰙЀ 呄ᠾ鹨់༹皧 ࠄ 00령ꐱ댁珵뛐珵Љ 䕄ྦ 뤂ᐱ뚜珵 ᴴᏩ呄ᠾ퍘ᒥ 鹨់ᩄ ꋔྦ 瑉浥 巠皱㙲皦抐皱 巠皱 ੨皦柘皱 ᅵ皥 ب 巠皱㙲皦忈皱 ੨皦柘皱 즠Ʋǜ 勁皦즠Ʋب ǜ V / 펔B䌁皦 ᮔDž '鱤džၜ먢䇨珵呈ᠾ뤂ᐱ ⿇⬿먲僧ᐱ㥲ᐲ�僬㣢ᐲ ᠾ 랖僧آ 識 �僬㣢ᐲ 臆S㥲ᐲ ᬄğ 識 理艏S杴 識杴 㥲ᐲ
-
10/29/2021
Advantages of VFD for HVAC System
One of the most successful energy management tools ever used in HVAC (Heating, Ventilating and Air Conditioning) systems of buildings is the Variable Frequency Drive (VFD).
-
09/18/2020
List of foreign medium and high pressure compressors in the Chinese market
When it comes to high-pressure compressors, they are not commonly used air compressors. They are widely used in pressure testing, chemical, bottle blowing, engineering, energy, electric power, military, medical and other industries. The general batch is relatively small, and domestic I think the high-pressure machine market is still in a budding state, and there is no more good capital and technical force to invest in this aspect of production;