There is no price at present, you can Request a Quote
In/Out diameter:DN 50/40
Maximum flow rate: 400 L/min
Maximum pumping head: 22/23 m
Standard flow rate: 200 L/min
Standard pumping head: 18.5 m
Motor power: 1.5 kW
Voltage: 220/380V
YIDA Magnet Pump XND-422
There is no price at present, you can Request a Quote
People who bought this item also viewed
PAN WORLD Magnet Pump NH-403PW-CV
ANEST IWATA Vacuum Pump DVSL-500CS5
Shurflo Diaphragm Pump 8020-833-238BX
CALPEDA Water Pump NM25/20BA
Burgmann Mechanical Seal H7N-35
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
KOGANEI Air Cylinder BDA10X5
Chint VFD Frequency Converter NVF300M-220/TS4
KEMET Capacitor R76UI122050H4J
NORGREN Air Cylinder RA/8125/160
Recent related posts
-
09/07/2020
Precautions for installation of mold core dryer
The mold core dryer adopts the latest mold core adsorption drying technology. It is an air compressor post-processing equipment. What matters should the enterprise pay attention to when installing the mold core dryer?
-
09/21/2020
Refrigeration system failure symptoms
Symptoms of refrigeration system failure 1. Detection of pressure and temperature of refrigeration system (1) The pressure concept of the refrigeration system The refrigeration system can be divided into high and low pressure during operation. The high pressure section is from the discharge port of the compressor to before the throttle valve. This section is called the evaporation pressure.
-
09/18/2020
Copeland compressor scroll series product introduction
The simple concept of Copeland Scroll compressor scroll was first invented in 1905. The scroll is an involute spiral, which meshes with the matching scroll as shown above, forming a series of gradually expanding spaces between the two components.
-
02/15/2024
Why is My Electric Furnace Blowing Cold Air? 11 Reasons&Ways to Fix
An electric furnace is a reliable and efficient way to keep your home warm during the colder months. However, encountering the issue of your electric furnace blowing cold air can be both frustrating and uncomfortable.
-
06/13/2020
This is the reason for the overheating of refrigeration compressor exhaust~!
This is the reason for the overheating of refrigeration compressor exhaust~! The main reasons for the exhaust temperature overheating are as follows: high return air temperature, large motor heating capacity, high compression ratio, high condensation pre 器2 䀀 ᅵ皥 䖒皦즠Ʋ煔क़ 㲈Ʋ 䌁
-
10/20/2021
Air Compressor Troubleshooting and Solutions
With the development of motor technology, compressor is considered as "general machinery", especially in coal chemical industry, machinery industry and other industries.
-
01/16/2021
Refrigerator compressor maintenance case
Refrigerator compressor maintenance case Case description: The repair is a Refrigerator 220 direct-cooled refrigerator, which starts after the contact is stuck, causing the refrigerator compressor to start normally and sometimes abnormally.
-
08/18/2020
Common faults and maintenance methods of air-cooled chillers
Air-cooled chillers are installed outdoors without any obstruction, and are easily affected by outdoor light. So how to maintain good ventilation, good environment and space has a key impact on the cooling effect of the chiller.
-
09/15/2020
The technical status and development trend of air compressor
I. Introduction Compressor is a machine used to increase gas pressure and transport gas, and belongs to a working machine that converts the power energy of the prime mover into gas pressure energy. It has a wide range of types and uses, and is known as "general machinery".
-
07/05/2020
Why is frost formed between the electronic expansion valve and the compressor
Why is frost formed between the electronic expansion valve and the compressor? A customer asked: The compressor is suddenly not cooling, and the electronic expansion valve is frosted to the compressor. Is there any relationship between the two before?