voltage supply range +Vs: 12-30 VDC
current consumption max. (no load): 35 mA
output circuit: PNP break function (NC)
output current: Less than 200 mA
voltage drop Vd: Less than 2 VDC
adjustment: potentiometer
Baumer Sensor UNDK 30P3712/S14
People who bought this item also viewed
Baumer Sensor CH-8501
Honeywell Sensor H7508B1080
Banner Sensor Q4XBLAF300-Q8
TAKEX Sensor GS20RN
TAKEX Sensor GSZ3SPN
Tyco Flame Detector 811FEX
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
VISHAY Capacitor 900V 50UF
WALRUS Water Pump TPCK2T22-13
Yuci Vane Pump YB-B92C-DU-FL-50
RICHTEK IC RT7738AAGE
MINDMAN Air Cylinder MCRQ-25A
Recent related posts
-
09/07/2020
Ten most commonly used parameters of frequency converters
There are many function parameters of the frequency converter, generally there are dozens or even hundreds of parameters for users to choose. In actual applications, it is not necessary to set and debug each parameter, most of which just need to use the factory settings.
-
07/21/2020
How to protect the refrigeration compressor, you must master the following knowledge!
When the compressor is running, some abnormal conditions may occur, such as: exhaust pressure is too high, suction pressure is too low, oil pressure is insufficient, motor is overheated, excess liquid enters the cylinder, etc. In the event of an abnormal situation, the compressor will be damaged if there is no protective measure.
-
08/14/2020
Factors affecting the boiling heat transfer of refrigerant liquid
In the evaporator, the heat of the cooled medium is transferred to the refrigerant through the heat transfer wall, so that the liquid refrigerant absorbs heat and vaporizes.
-
09/10/2020
The management method of the air compressor room of the Red Fifth Ring
1. Choose a wide and well-lit place to facilitate the space and lighting required for the operation, maintenance and repair of the air compressor.
-
06/14/2020
Precautions for the operation of cold storage equipment
Precautions for the operation of cold storage equipment 1. For the evaporator of the air-cooled machine: always check the defrosting situation, whether the defrosting is timely and effective, it will affect the cooling effect and cause the liquid return 器2 䀀 ᅵ皥
-
08/17/2020
The heat pump is prone to frost between +4~-4℃. The symptoms and reasons are not beyond these 10 points.
The air source heat pump can use the low-grade heat energy in the ambient air, so it has the dual advantages of energy saving and environmental protection. However, one of the problems is that
-
06/14/2020
Working principle of York screw compressor
Working principle of York screw compressor Working principle of York screw compressor, screw compressor is a volumetric compression machine with working volume for rotary motion. The compression of gas depends on the change in volume, and the change in v 器2 䀀 ᅵ皥 䖒皦즠Ʋ奌ི 㲈Ʋ 䌁皦 ᮔDž༬皧奖ིЀ 呄ᠾ鹨់༹皧 ࠄ
-
06/14/2020
Scientists use magnetic fields and deformed alloys to develop refrigeration systems
Scientists use magnetic fields and deformed alloys to develop refrigeration systems Apart from redundant functions such as touch screens and built-in cameras, basic refrigerator technology has not changed much in decades.
-
07/05/2020
Full analysis of high-temperature burn-down failure of scroll compressor
Full analysis of high-temperature burn-down failure of scroll compressor Scroll compressor overheating at high temperature for a long time will not only reduce the insulation performance and reliability of the motor, shorten the life of the motor, but also reduce the lubricating ability of the lubricating oil, and even cause carbonization and acid hydrolysis of the lubricating oil.
-
01/17/2023
How does Variable Valve Timing Work?
The valve timing system of a traditional engine is a mechanical system in which the valve timing (i.e., valve opening and closing) remains unchanged.