BANDO Belt B-480
People who bought this item also viewed
GATES Belt HTD 1890-3M
SYNCHROFLEX Belt AT 3/501
SYNCHROFLEX Belt AT 5-455
COKERY Belt B130
SYNCHROFLEX Belt AT 5-340
Yaskawa Servo Motor SGMG-13A2ABB
JSCC Speed Reducer 90GF6H
ASLONG Electric Motor JG37-3429
DIAMOND Industrial Chain 140H
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
Delta Fan PFB0848EHE
TYCO Relay KHU-17A18N-120
SMC Solenoid Valve SY7220-5GD-02
PMI Linear Guideway MSR45LSSSF0H
LR-LINK NIC Card LREC7210PF-SFP
Recent related posts
-
07/28/2020
Method and steps to replace the refrigeration compressor
Cut off the power supply: Before replacing the compressor, be sure to cut off the power supply of the unit, otherwise there will be a risk of electric shock.
-
07/21/2020
11 common protection devices for refrigeration compressors
When the compressor is running, some abnormal conditions may occur, such as: exhaust pressure is too high, suction pressure is too low, oil pressure is insufficient, motor is overheated, excess liquid enters the cylinder, etc. In the event of an abnormal situation, the compressor will be damaged if there is no protective measure.
-
06/14/2020
Broken refrigeration compressor bearings? What can be repaired? Which must be thrown?
Broken refrigeration compressor bearings? What can be repaired? Which must be thrown? How to judge whether the bearing can be used again and the defects of the bearing need to be replaced To determine whether the bearing can be used again, it should be 器2 䀀 ᅵ皥 䖒皦즠Ʋ嫜ི 㲈Ʋ 䌁皦 ᮔDž༬皧嫦ིЀ 呄ᠾ鹨់༹皧 ࠄ 00령ꐱ댁珵뛐珵Љ 䕄ྦ 뤂ᐱ뚜珵 ᴴᏩ呄ᠾ퍘ᒥ 鹨់ᩄ ꋔྦ 瑉浥 巠皱㙲皦抐皱 巠皱 ੨皦柘皱
-
06/14/2020
Correct treatment method after refrigeration compressor burned out
I. Introduction: If the compressor burns down or mechanical failure or wear has caused the inevitable pollution of the refrigerant system, the situation is as follows:
-
08/20/2020
Introduction of solenoid valve and troubleshooting method
1. Symptoms-the solenoid valve does not open possible reason: 1 The coil has no voltage. 2 Incorrect voltage/frequency 3 Coil burned out 4 Pressure
-
03/28/2024
High-Performance Drive Solutions: Innovation and Development of Servo Motors in Robotics
In recent years, robotic technology has been widely used in industrial production, service industries, medical care and other fields. The motion control of robots is the key to achieving various complex tasks.
-
06/30/2022
Types of Check Valve
Depending on the design of the check valve, they will operate slightly differently. The most common check valve is a spring loaded in-line check valve, however, we will discuss multiple types below.
-
07/14/2020
What are the reasons why the air conditioner is not cooling?
What are the reasons why the air conditioner is not cooling? In summer, people turn on the air conditioner mainly to get a cool feeling, but they did not find that the air conditioner has not been cold for a long time. The air conditioner is not cooling. What are the reasons why the air conditioner is not cooling? Many air conditioners are not cooling, because it is faulty Problem, so it is necessary to repair it, what are the ways to repair the air conditioner?
-
07/23/2020
Reasons for excessively high discharge temperature of refrigeration compressor (technology sharing)
The refrigeration compressor is the core and heart of the refrigeration system. The capacity and characteristics of the compressor lead to the capacity and characteristics of the refrigeration system. In a sense, the design and matching of the refrigeration system is to reflect the capacity of the compressor.
-
07/31/2020
Principle analysis of monitoring system for cold and heat source equipment
The building automation system is an integrated system platform, in which many subsystems have diverse functions and complex engineering. What is the principle of the cold and heat source equipment monitoring system as one of the many subsystems of the building automation system?