Series 600 J
Material:fiberglass-reinforced plastic.Impeller PA,housing PBT
Mass:100 g
Ebmpapst Fan 612J/2H
People who bought this item also viewed
Ebmpapst Fan W2D250-EA26-21
Ebmpapst Fan A2E210-AF02-09
Delta Fan QFR0824UHP0
Ebmpapst Fan M4E074-GA
Ebmpapst Fan D2D160-BE02-11
Ebmpapst Fan 7056ES
Ebmpapst Fan S4D350-AP22-62
Delta Fan FFB2024LT
Nidec Fan M35133-58
SUNON Fan MF40101V2-C01C-A99
Ziehl Abegg Fan RH31M-4EK.2C.1R
Copeland Compressor ZR81KC-TFD-522
Block Transformer VC16/2/9
Fuji Contactor SC-N11M8-C
BROAD-OCEAN Electric Motor Y5S413B899
Kuroda Module A49PB-16UJ-4Y239
Pilz Relay 774063
MUNDORF Capacitor 750V 20UF
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
KUDOM Relay KSJ1200D
BANDO Belt T5-850-20
Emerson Vertiv Air Conditioner DME17MHOUP1
Recent related posts
-
01/10/2023
5 Refrigeration Solenoid Valve Failures and the Solutions
Refrigeration solenoid valve is an industrial equipment controlled by solenoid. It adjusts mass direction, flow, speed and other parameters in industrial control systems.
-
09/04/2020
10 reasons why the compressor industry should participate in foreign exhibitions
I heard that there are some foreign exhibitions in the air compressor industry? Does it make sense to run so far to participate?
-
06/29/2020
Analysis of the cause of excessive suction temperature of compressor
Analysis of the cause of excessive suction temperature of compressor The high suction temperature is mainly due to the increase of superheat of suction. Note that high suction temperature does not mean high suction pressure, because the suction is superheated steam. Under normal circumstances, the compressor cylinder head should be half cold and half hot. If the suction temperature is too high, the cylinder head will all heat up.
-
06/14/2020
Is PVC or PE good for domestic fresh air system pipes
Is PVC or PE good for domestic fresh air system pipes Fresh air system is a category of light equipment and heavy design. Fresh air equipment is highly dependent on design and construction.
-
06/23/2020
What is the reason why the freezer is not cooling
It may be that the capillary is blocked and the refrigerant flow does not enter the evaporator. It may also be that the refrigerant needs to be replenished or the refrigeration system is leaking. If the buffer tube inside the compressor ruptures, there may be loose screws or it will cause no cooling. It is also possible that the expansion valve and the discharge valve are not adjusted properly, causing cold air to leak out. Need to check one by one, and then take the medicine.
-
07/01/2020
Why does the centrifugal Taikang compressor have such a high speed
Why does the centrifugal Taikang compressor have such a high speed Centrifugal compressors require speed during operation, and the speed is very high. However, many people do not understand, why does a centrifugal compressor need such a large speed? Let us take a centrifugal Taikang compressor as an example to explain this problem for everyone.
-
06/29/2020
Time node of compressor refrigeration oil replacement
Time node of compressor refrigeration oil replacement 1. The long-term operation of the entire refrigeration system, after the initial maintenance, if there are no special circumstances, the compressor refrigeration oil should be replaced when the refrigeration system working time reaches 10,000-12,000 hours.
-
11/30/2023
A Complete Guide to CPU Liquid Coolers: Composition, Working Principle, Types, and Pros and Cons
With increasing requirements for computer hardware and operating speed, there are higher and higher requirements for the cooling performance of computers.
-
08/26/2020
Overview of Screw Refrigeration Compressor Technology
Screw compressors, also known as screw compressors, are divided into single screw compressors and twin screw compressors. The single screw compressor was developed by Sinn, France in the 1970s.
-
08/21/2020
Causes and troubleshooting of industrial chillers
1. High condensing pressure (higher than the specified value) failure causes and remedies: ① Non-condensable gas in the system: release non-condensable gas.