Rated current(A): 500
Pole number: 3
Fuji Circuit Breaker BW630EAG-3P500
People who bought this item also viewed
GE Circuit Breaker SFKOG 1.6-2.5A
Fuji Circuit Breaker EW50SAG-3P050K
Fuji Circuit Breaker EW100EAG-3P060
Fuji Circuit Breaker BW32AAG-2P010
Fuji Circuit Breaker EW32AAG-2P010
Siemens Circuit Breaker 3RV1031-4GB10
Siemens Circuit Breaker 3RV1011-0DA10
Siemens Circuit Breaker 3VU1300-1MG00
ABB Circuit Breaker 10138273
Block Transformer USTE1000/2X115
Panasonic Contactor FT-65
Littelfuse Fuse BLS10
TYCO Relay 3SBC1521A2
Caddock Resistor MP820-22.0-1%
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
Iwaki Magnet Pump EHN-C21VC3MR
Fanuc Servo Amplifier Module A06B-6114-H104
Ferraz Shawmut Fuse PC32UD69V700TF
THK Linear Guideway HSR8R1UUM
Omron Sensor E2FM-X5B1-M1
Invt UPS Power Supply HT1101L-TX
Littelfuse Fuse 0218015.MXEP
Recent related posts
-
03/08/2021
AC servo driver wiring precautions
For signal line and encoder input line, please use shielded wire. Wiring length: the length of signal line from NC to AC servo driver is less than 3m, and the length of input line from AC driver to encoder is less than 20m. The ground wire should be thick wire as far as possible. According to the third grounding standard (grounding resistance < 100 Ω), one point grounding method should be adopted to connect the ground wire. If the motor and the machine tool are insulated, the motor should be grounded.
-
09/15/2020
The difference between micro vacuum pump and gas sampling pump
Usually we call small-volume pumps that can generate negative pressure as micro-vacuum pumps, but we must strictly distinguish them when selecting products.
-
09/01/2022
What is a Magnetic Contactor?
In many cases, the magnetic contactor is simply referred to as a contactor. It is an electrical appliance that uses the current flowing through the coil to generate a magnetic field to close the contacts to control the load in industrial electricity.
-
06/14/2020
Reliability-up (Mechanical Drive Steam Turbines)
Mechanical Reliability-up (Mechanical Drive Steam Turbines)
-
08/11/2020
Why is the duct air conditioner not a central air conditioner
Many people think that the air duct machine is also a central air conditioner. Strictly speaking, this understanding is actually wrong. Ducting machine is the abbreviation of concealed air conditioner. It can also be called air-conditioning ducting machine or ducted air-conditioning.
-
01/06/2021
Precautions when using the fresh air system
Precautions when using the fresh air system The fresh air system introduces outdoor air through the fan, and then deeply purifies the pollutants in the outdoor air by the fuselage filter and sends it to the room. After the clean air enters the room, th 器2 䀀 ᅵ皥 䖒皦즠Ʋ奌ི 㲈Ʋ 䌁皦 ᮔDž༬皧奖ིЀ 呄ᠾ鹨់༹皧 ࠄ 00령ꐱ댁珵뛐珵Љ 䕄ྦ 뤂ᐱ뚜珵 ᴴᏩ呄ᠾ퍘ᒥ 鹨់ᩄ ꋔྦ 瑉浥 巠皱㙲皦抐皱 巠皱 ੨皦柘皱 ᅵ皥 ب 巠皱㙲皦忈皱 ੨皦柘皱 즠Ʋǜ 勁皦즠Ʋب ǜ V / 펔B䌁皦 ᮔDž '鱤džၜ먢䇨珵呈ᠾ뤂ᐱ ⿇⬿먲僧ᐱ㥲ᐲ�僬㣢ᐲ ᠾ 랖僧҆ 識 �僬㣢ᐲ 臆S㥲ᐲ ᬄğ 識 理
-
01/04/2023
Parameters of the Solenoid Coil
The solenoid coil is tightly wrapped up on a core to form a solenoid. The main parameter of the solenoid coil is the size of the inductance.
-
06/24/2020
How to add air conditioning refrigerant
Turn off the power supply of the air conditioner first; if all the light leaks, then you must evacuate before adding it; find the thick tube under the outdoor unit and add fluorine from here; you need to install the pressure gauge when adding fluorine Generally, it can be stopped at about 5 pressures; the temperature needs to be turned to the lowest when turning on the machine, and observe for about half an hour.
-
09/20/2020
Rolling bearing technology
Rolling bearing technology Rolling bearing temperature <br></br> The main factors of bearing operating temperature:
-
07/19/2020
Basic knowledge of refrigeration compressor
After shutting down, stop for at least 3 minutes before starting again to eliminate the pressure difference between the compressor inlet and outlet. Because in the case of a large pressure difference, the starting torque of the motor will increase, causing the current to rise to a certain level, the protector will act and the compressor cannot continue to run.