clearance. In conventional condition of 1500r/min and 250bar, the volumetric efficiency can
reach above 94%.
Ultra-low noise. It adopted with high-strength cast iron and unique internal sound-absorbing
design to make the noise even lower. For example, the noise of HG2-100 is less than 70dB at
1500r/min and 250bar.
High pressure design. The maximum working pressure can reach to 350 bar at rated speed.
Wide speed range. The maximum speed is up to 3500r/min.
Strong stain resistance. It can maintain long life even in harsh environments.
HYTEK Gear Pump HG2-125-01R-VPC-F-36-1
People who bought this item also viewed
Sumitomo Gear Pump QT62-125F-BP-Z
KOMPASS Check Valve MSSA-02-Y-A25
Daikin Piston Pump VZ63C23RJAX-10
KCL Vane Pump VPKC-F40-A4-B
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
IFM Sensor IN5262
MERKEL Oil Seal T20 80-92-8.7
Recent related posts
-
06/13/2020
How to protect the refrigeration compressor, you must master the following knowledge
When the compressor is running, some abnormal conditions may occur, such as: the discharge pressure is too high, the suction pressure is too low, the oil pressure is insufficient, the motor is overheated, and excessive liquid enters the cylinder. If an ab 器2 䀀 ᅵ皥 䖒皦즠Ʋ嫜ི 㲈Ʋ 䌁皦 ᮔDž༬皧嫦ིЀ 呄ᠾ鹨់༹皧 ࠄ 00령ꐱ댁珵뛐珵Љ
-
06/13/2020
What's going on with frost during refrigeration compressor operation
Whether the compressor will frost depends on the evaporation temperature of the system and the superheat of the return air. The dry storage evaporator system of cold storage and refrigerator freezer, the refrigeration system under standard working conditi 器2 䀀 ᅵ皥 䖒皦즠Ʋ煔क़ 㲈Ʋ 䌁皦 ᮔDž༬皧煞क़Ѐ 呄ᠾ鹨់༹皧 ࠄ 00령ꐱ댁珵뛐珵Љ 䕄ྦ 뤂ᐱ뚜珵 ᴴᏩ呄ᠾ퍘ᒥ 鹨់ᩄ ꋔྦ 瑉浥 巠皱㙲皦抐皱 巠皱 ੨皦柘皱 ᅵ皥 ب 巠
-
09/10/2020
The management method of the air compressor room of the Red Fifth Ring
1. Choose a wide and well-lit place to facilitate the space and lighting required for the operation, maintenance and repair of the air compressor.
-
06/13/2020
Magnetic suspension refrigeration technology is expected to become the mainstream trend of refrigeration in the future
Magnetic suspension refrigeration technology is expected to become the mainstream trend of refrigeration in the future "With the elaborate construction of data center refrigeration systems,
-
08/26/2020
Mobile screw machine requirements for lubricating oil
The requirements of the mobile screw machine for lubricants are as follows 1. The volume of the mobile screw machine and the volume of the oil tank are small, the amount of lubricating oil is also small, and the oil temperature is higher during operation,ﰨ2 䀀 湠皟 V ǜ V 㠠ǝ㠠ǝ㠠ǝ類 湠皟᳥皓ώႡЀ 뇀Ⴔ湠皟 蘵皒 㠠ǝ ㋐ݗ痌律
-
06/25/2020
How to distinguish between screw refrigeration compressor and piston refrigeration compressor
Distinguish from type Screw refrigeration compressors and piston refrigeration compressors are both volumetric compressors, and screw refrigeration compressors are a new type of high-speed refrigeration compressors.
-
06/13/2020
Refrigeration compressors have five major technological
Refrigeration compressors have five major technological developments around energy saving CFCs and HCFCs refrigerants that have a destructive effect on the ozone layer are phase-out substances specified in the Montreal Protocol
-
05/10/2022
What is PLC?
Programmable logic controller (PLC) is a digital operation electronic system specially designed for application in industrial environment.
-
01/08/2024
Cooling Tower Troubleshooting and Solutions
Cooling towers are commonly used equipment in industry, air conditioning and other fields, and are used to remove the large amounts of heat generated during the production process.
-
08/05/2020
What are the common faults of the cut-off foot of the chiller and the adjustment cabinet
1. The valve body of the valve of the chiller is mostly steel castings. Casting blisters may be formed during the production process, causing the valve to leak refrigerant during use.