Mitsubishi Servo Drive MR-E-20A-QX002
People who bought this item also viewed
Mitsubishi Servo Drive MR-J2S-100A
Mitsubishi Servo Drive MDS-B-V2-3535
Mitsubishi Servo Drive MR-J2-100CT
Mitsubishi Servo Drive MDS-B-SVJ2-03
Sanyo Denki Servo Drive RBD2CT202
Sanyo Denki Servo Drive RS1L01AE0H2
Mitsubishi Servo Drive MDS-A-SVJ-10
Fanuc Servo Drive A06B-6164-H333#H580
Panasonic Servo Motor MDMF502L1D5
YUKEN Servo Valve SVD-F11-19-7.5-21
Rockwell A-B HMI 2711P-86C20D
SIEMENS Actuator GEB132.1E
OMRON Power Supply S8VM-10012C
MITSUBISHI Spindle Amplifier MDS-A-SPJ-37
Beckhoff Module BC9050
HANYOUNG Relay TF62N-D
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
Contrinex Sensor DW-AD-502-P8
Balluff Sensor BES00C3
Delta HMI DOP-B03S210
Eaton Moeller Circuit Breaker IZM91N3-V16CW
Recent related posts
-
06/14/2020
New energy efficiency standards for air conditioners are officially implemented
New energy efficiency standards for air conditioners are officially implemented Recently, a major event has occurred in the air-conditioning industry, and the new energy efficiency standard has confirmed the implementation time.
-
06/20/2020
What are the causes of air conditioning trip
What are the causes of air conditioning trip 1. The contradiction between the rated current of the air conditioner and the current carrying capacity of the wire. Here are two formulas involved: ①The rated current of air conditioner I=P÷U ÷power factor, the power remains unchanged, the smaller the voltage, the greater the current required. ② The current carrying capacity of the wire I=U÷R, the voltage is proportional to the current. So when the power supply voltage is normal, we must consider the line voltage drop. The longer the line, the greater the resistance, the greater the voltage drop, and the smaller the output current at the end. However, because the power of the load remains unchanged, the voltage becomes smaller, and the current that needs to be output will be larger. At this time, the wire is forced to overload, and the time will cause heating, and eventually cause the tripping of the open circuit. Some friends said that the heat of the wire will not cause the tripping of the circuit breaker. In fact, the manufacturer of the air switch has made it clear in the relevant manuals that the heat of the wire will cause the air switch to trip. Because the wire heats up, the crimp terminal will also heat up, and the resistance will become larger and larger. The larger the resistance, the greater the current consumption, and the hotter it will be, a vicious cycle. 2. Leakage During the daily maintenance work, we will encounter the situation that the air circuit trips due to the leakage of electricity. At least I have not experienced it once or twice. Regardless of the leakage of the neutral line or the leakage of the live line, a long time will cause the circuit breaker to trip. Why does the electric leakage cause the MCB to trip? There are two situations. ① Good grounding. At the beginning, the leakage current was not large, and as time went by, the leakage current became larger and larger, and eventually evolved into a short circuit to ground, unable to close. ②There is no ground wire. If the equipment is not connected to the protective ground, when the wire leaks to the equipment, it is equivalent to adding a large shunt resistance. Like this problem, if the air conditioner does not have a ground wire, when the wire leaks to the air conditioner, the air conditioner is a very large shunt resistor and will consume a lot of current. Eventually, the wire will heat up or trip open. How to determine whether the trip caused by the above two aspects can be done with a clamp ammeter. ① Measure the voltage at the input and output to see if there is a significant change in voltage drop. ②Measure whether the output current exceeds the standard. So my suggestion is: first measure the supply voltage to see if it is within the allowable fluctuation range. Then measure the current to see if it exceeds the rated ampacity of the wire. Finally, check the data one by one according to the measured data to find out the reason.
-
09/02/2020
The structure and function of the air compressor PLC product upgrade
The CPU is mainly composed of arithmetic units, controllers, registers and data, control and status buses that realize the connection between them. The CPU unit also includes peripheral chips, bus interfaces and related circuits.
-
03/07/2022
Seven Reasons Why your LG Refrigerator Not Cooling
As times go by and society is developing, refrigerators make people’s life more convenient.
-
09/18/2020
Jingliang Electronics-Air Compressor Sensor Solution
——High-quality, cost-effective to provide customers with perfect sensor solutions Precision Electronics-MEAS (MSI) Sensor Co., Ltd. is a precision electronic engineering expert who masters the world's leading silicon micromachining MEMS technology.
-
08/11/2020
Installation specification for mainframe of refrigeration unit
he closer the main unit of the refrigeration unit is to the evaporator, the better it is easy to maintain and has good heat dissipation. If it is moved outside, it needs to install a canopy.
-
07/25/2020
90% of the compressor burns down due to these reasons (Refrigeration Oil)
The common faults of compressors mainly include the following three types: 1. Motor burns; 2. Oil shortage caused by refrigerating oil; 3. Liquid shock.
-
02/23/2022
Causes of Oil Separator Burning
During the use of your air compressor, there could be tricky oil separator burning failures.
-
01/02/2024
High Performance Solution for Medical Equipment Cooling (SANYO San Ace G Proof Fan)
Nowadays, cooling fans have been used in all walks of life, from simple electronic devices to high-end intelligent products, smart homes, car seat cushions, medical equipment, etc.
-
08/04/2020
This button on the remote control of the air conditioner is not used. Here is the secret of power saving →
Summer is here, and many families have begun to use air conditioners, but while enjoying the coolness, the rising electricity bills are also painful. I will teach you some power saving methods right away