The heat pump is prone to frost between +4~-4℃. The symptoms and reasons are not beyond these 10 points.
The air source heat pump can use the low-grade heat energy in the ambient air, so it has the dual advantages of energy saving and environmental protection. However, one of the problems is that the evaporator will frost when heating in areas with low temperature and high relative humidity. . The greater the relative humidity of the air, the more severe the frost on the coil.
The heat pump is prone to frost between +4~-4℃. The symptoms and reasons are not beyond these 10 points.
Generally speaking, when the relative humidity of outdoor air is less than 50%, frost is rarely formed. When the outdoor air temperature is lower than -5°C, the absolute moisture content in the air is small and frost formation is reduced. When the ambient temperature is between +4~﹣4℃ and the relative humidity is >85%, frosting z* is serious, and the higher the humidity, the more frosting, and the number of defrosting per day.
Generally speaking, frosting of air energy heat pumps is normal. General heat pump products have automatic frosting function to ensure the normal operation of the unit. Most dealers, especially novices, don't have to panic when they see defrosting. However, if it is severe, the frost layer will increase the air flow resistance, resulting in a decrease in the flow of the fan, deteriorating the performance of the air source heat pump system, and even affecting its normal operation, causing accidents such as the burning of the compressor. The performance and solution of the fault is nothing more than the following.
The heat pump is prone to frost between +4~-4℃. The symptoms and reasons are not beyond these 10 points.
Recent related posts
-
08/17/2020
The heat pump is prone to frost between +4~-4℃. The symptoms and reasons are not beyond these 10 points.
The air source heat pump can use the low-grade heat energy in the ambient air, so it has the dual advantages of energy saving and environmental protection. However, one of the problems is that
-
08/17/2020
The function and setting of the oil trap in the refrigeration system
In the Fuli Subaru refrigeration and air-conditioning system, when the main engine is higher than the end (evaporator), there is a riser pipe between the evaporator and the main suction pipe,
-
08/17/2020
The function and selection method of throttling capillary in industrial chiller
The capillary tube in the industrial chiller is a pure copper tube with a specified length and a very thin diameter. Its inner diameter is generally between 0.5-2mm. Choose the appropriate length according to the size of the chiller, and then process it i碌7館2 䀀 締眪
-
08/17/2020
The difference between a single-head chiller and a double-head chiller
1. Single-stage refrigeration system 1. The single-stage refrigeration cycle refers to the four processes of compression, condensation, throttling,
-
08/17/2020
Temperature has a great influence on refrigeration and air-conditioning systems, don’t you know
The relevant temperature of the components of the refrigeration and air-conditioning system has a normal temperature range, and it is an abnormal state if it exceeds this range.
-
08/17/2020
Structural requirements of modular air conditioning units
1. When the windward velocity of the cooling coil exceeds 2.5m/s, a water baffle shall be set. 2, the spray section should have an observation window, a water baffle and a water filter device.
-
08/17/2020
Regulations to be observed in the use of cold rooms in civil cold storage
1. Pozzolanic cement and slag cement mixed with pozzolanic materials shall not be used in the cold room of civil construction cold storage; different types of cement shall not be mixed, and two types of cement shall not be used for the same component.
-
08/17/2020
Reasons and repair methods of screw damage of screw chiller
Screw chillers are named after the use of screw compressors. They are often used in large-scale industrial refrigeration such as chemical plants and central air-conditioning systems. Because the performance of screw chillers is more stable and efficient,
-
08/17/2020
Problems that need attention in the use, installation and maintenance of air-cooled chillers
Air-cooled chillers have many advantages in terms of performance, which makes it more and more widely used, and its advantages such as small footprint and fully computerized automatic control operation management mode have been favored by more enterprise 碌7館
-
08/17/2020
Principle analysis and characteristics of new technology machines for central air conditioning
1. Water magnetization treatment technology Using the magnetic field effect to treat water is called magnetization treatment of water.
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
PIZZATO Switch FR 576-K21
MINDMAN Air Cylinder MCMB-13-25-200
Omron PLC NX-END02
Sanyo Denki Fan 109R0812T4F041
AirTAC Air Cylinder ACQ63X80S
Schneider Sensor XS4P30NA370D