The life of air compressor bearings and the causes of damage
If the air compressor loses one bearing or does not pay attention to the correct use of the bearing, the air compressor will not be able to operate normally, and it will greatly shorten the service life of the bearing, which will bring us unnecessary losses. So below, the editor of okmarts.com will analyze the life of air compressor bearings and the causes of damage.
1. Improper installation (about 16%)
1. Using brute force during installation, directly hitting the bearing with a hammer will damage the bearing the most, which is the main cause of deformation.
2. The installation is not in place, the installation is deviation or the bearing is not installed, resulting in too small bearing clearance. The inner and outer rings are not at the same center of rotation, resulting in misalignment.
Recommendation: Choose appropriate or professional bearing installation tools, and use special equipment to test after installation.
2. Poor lubrication (about 50%)
According to the investigation, poor lubrication is one of the main causes of premature bearing damage. The main reasons include: the special lubricant or lubricating oil for the air compressor was not filled in time; the lubricant or lubricating oil was not filled in place; the lubricant or lubricating oil was not properly selected; the lubrication method was incorrect and so on.
Suggestion: Choose the correct lubricant or lubricating oil and use the correct lubrication filling method.
3. Pollution (about 14%)
Pollution can also cause premature bearing damage. Pollution means that sand, dust, metal chips, etc. enter the inside of the bearing. The main reasons include: opening the bearing package too early before use, causing pollution; the working environment is not clean during installation, causing pollution; the working environment of the bearing is not clean, and the working medium is polluted.
Suggestion: It is best not to unpack the bearing before use; keep the installation environment clean during installation, clean the bearing to be used; strengthen the sealing device of the bearing.
Fourth, fatigue (about 34%)
Fatigue damage is a common damage method for bearings. Common causes of fatigue damage may be: long-term overload operation of air compressor bearings; failure to repair in time; improper maintenance; equipment aging.
Suggestion: Choose the appropriate bearing type and replace the fatigue bearing regularly and in time.
The above is the most common cause of bearing damage and greatly shortened bearing life! As long as we use it correctly and maintain it well in our daily life, then the air compressor bearings will work well for us!
The life of air compressor bearings and the causes of damage
Recent related posts
-
09/08/2020
The life of air compressor bearings and the causes of damage
If the air compressor loses one bearing or does not pay attention to the correct use of the bearing, the air compressor will not be able to operate normally, and it will greatly shorten the service life of the bearing, which will bring us unnecessary losses.
-
09/08/2020
The function and basic performance of the pressure reducing valve of the compressed air filter
The filter, pressure reducing valve and lubricator together form a pneumatic triplet. The filter is mainly responsible for filtering the liquid water, oil and impurities in the compressed air, the pressure reducing valve is mainly responsible for controlling the system pressure, and the oil mist device is responsible for the oil lubrication of the back-end components.
-
09/08/2020
The evolution history of air compressors
The (mechanical) vacuum pump made in Germany in 1640 is the originator of modern air compressors. Around 1800, the first single-stage (reciprocating piston) air compressor was made in the UK, and its discharge pressure was 1.38MPa (gauge pressure).
-
09/08/2020
The difference between drying equipment, dryer and dryer
Drying equipment, also known as dryers and dryers, is used for drying equipment, which vaporizes the moisture (generally refers to moisture or other volatile liquid components) in materials through heating to obtain solid materials with specified moisture content .
-
09/08/2020
The difference between air-cooled and water-cooled screw air compressors
The difference between air-cooled screw machine and water-cooled screw machine: The oil cooler of the air-cooled screw compressor and the compressed air after-cooler are made into one body. It is an aluminum plate-fin structure and brazed in a vacuum furnace. Once the oil leaks, it is almost irreparable and only replaced. The working principle is that hot oil and high temperature (about 80℃) gas flow in their respective pipes,
-
09/08/2020
The development trend of compressed air post-treatment dryer
Regarding the compressed air post-treatment dryer equipment currently on the market, from the perspective of technology and treatment effects, traditional compressed air post-
-
09/08/2020
The development of laboratory air compressors has become the mainstream trend of the market
In recent years, professional air compressor manufacturers in laboratories have made a lot of technical and commercial tentative research, development and innovation attempts driven by the tide of the industrial Internet, but on the whole, the results achieved are not very satisfactory ( Mainly for the screw laboratory professional air compressor market).
-
09/08/2020
The development history of air compressor
A device used to increase air pressure. We call it an air compressor. There are thousands of types. The most common ones are piston air compressors, screw air compressors, scroll air compressors, and sliding vane air.
-
09/08/2020
The characteristics of the main shaft of the frequency conversion screw air compressor
The main core of the equipment operation of the rod host during the operation of the variable frequency screw air compressor. Without the rod host equipment, the equipment cannot operate normally. The following is an explanation of the characteristics of the rod host used in the air compressor equipment:
-
09/08/2020
The basic theoretical knowledge of air that everyone who uses an air compressor should understand
1 What is air? What is normal air? Answer: The atmosphere around the earth, we are accustomed to call it air. The air under the specified pressure of 0.1MPa, temperature of 20°C and relative humidity of 36% is normal air. Normal air is different from standard air in temperature and contains moisture. When there is moisture in the air, once the moisture is separated, the air volume will be reduced.
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
ANLY Relay ASY-2D DC24V 9.9m
LG LS Relay GMP22-3T 5A
Sanyo Denki Fan 109R0848K4D011
Contrinex Sensor PL-M18S-A3-010F