What should I do if the screw compressor fails
Nowadays, in the summer, the use of air conditioners is increasing. If the screw compressor fails, how to repair it? First, check out where the fault is. After the inspection, repair or replace the damaged parts, as follows:
1. For less severe wear and fuzzing, it can be smoothed by fitter with oilstone. The surface of the rotor journal and the static and dynamic rings of the shaft seal shall not have any defects such as corrosion or cracks. After the surface of the main journal is polished, its dimensions should be carefully measured, and the main bearing should be adjusted based on this.
2. If the main bearing is severely worn and exceeds the clearance limit for the shaft, it should be replaced. If the bearing alloy is cast, the coaxiality of the inner surface and the bearing hole must be ensured.
3. If the thrust bearing is damaged or the clearance increases, it must be replaced with a new one. And the size of the vacuum clearance should be measured, and the bearing adjustment pad should be equipped on this basis.
4. All gaskets and "O" rings must be replaced if they are damaged. The gasket can be processed by yourself, but be careful not to break or crack near the bolt hole to avoid leakage. The gasket should be made of high-quality materials. The "O" ring should be made of materials suitable for the refrigerant.
5. Clean the sealant on both ends of the body and the flat surface of the suction and exhaust end seats. Be careful not to scratch the surface.
Of course, the compressor is the "heart" of the entire air conditioner, so it is recommended to find a professional to deal with the problem first.
What should I do if the screw compressor fails
Recent related posts
-
08/14/2020
What should I do if the screw compressor fails
Nowadays, in the summer, the use of air conditioners is increasing. If the screw compressor fails, how to repair it? First, check out where the fault is. After the inspection, repair or replace the damaged parts, as follows:
-
08/14/2020
What should I do if the refrigerator trips and leaks
Leakage of the moisture-proof wire of the freezer The leakage of the moisture-proof wire of the freezer is mainly manifested by the frequent on and off of the overload protection relay that is turned on after the power is turned on
-
08/14/2020
What issues need to be considered in the construction of logistics warehouse cold storage
1. Location Logistics warehouse cold storage is generally built in a location with cheap land price and relatively convenient transportation according to the development of the enterprise.
-
08/14/2020
What is the hazard of high temperature to compressor motor and lubricating oil
The heat generated by the compressor during normal operation should not cause overheating. Normal motor heating, compression heat and friction heat have been carefully considered when designing the compressor,
-
08/14/2020
What are the performance advantages of air-cooled chillers
The rapid development of the refrigeration industry has brought a lot of convenience to people's lives, especially in the chemical and medical fields, and the demand for chillers in the food field is higher.
-
08/14/2020
What are the parts of the electrical installation of cold storage engineering installation
What are the parts of the electrical installation of cold storage engineering installation The electrical installation of cold storage engineering can include overhead lines, lighting, cables, machine room wiring, workshop or factory area power transformation and distribution.
-
08/14/2020
What are the noteworthy issues in central air conditioning design
1. Variable air volume ratio The air-conditioning system runs under partial load conditions most of the year, that is to say, the fans, ducts and air volume of the end of the variable air volume system are mostly between the maximum and minimum air volume limits.
-
08/14/2020
Two or three things about quick-freezing, come and see!
1. What is a quick freezing warehouse<br></br> Quick-freezing cold storage refers to a method in which food quickly passes through its largest ice crystal formation area and freezes quickly when the average temperature reaches -18°C.
-
08/14/2020
Trouble shooting and correct selection method for thermal expansion valve debugging
As we all know, the thermal expansion valve is one of the four major components in the refrigeration system. It is responsible for reducing the refrigerant from the condensing pressure to the evaporating pressure in the system
-
08/14/2020
Tips for troubleshooting the refrigeration system of low-temperature chillers
Regular maintenance work for the low-temperature chiller, while troubleshooting the refrigeration system of the low-temperature chiller is also very important.
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
KSK Oil SealTC(FKM)55X65X10
SHAKO Air Cylinder JCDA20B45
Puls Power Supply CP20.241-R2-C1