Tips for troubleshooting the refrigeration system of low-temperature chillers
Regular maintenance work for the low-temperature chiller, while troubleshooting the refrigeration system of the low-temperature chiller is also very important. Here is a brief introduction to some low-temperature chiller refrigeration system failure tips for your reference!
1. Exhaust at double pressure, heat dissipation may be problematic.
When it is detected that the high and low pressure of the system are higher than normal, it is generally because there is air in the system or excessive refrigerant is added. At this time, it is necessary to re-evacuate and add proper amount of refrigerant to solve the problem. But there is another situation, that is, poor heat dissipation, especially when the ambient temperature is relatively high, which often results in worse heat dissipation. The cause of this failure is generally the blockage of the heat sink, dirt, and insufficient speed of the heat dissipation fan.
2, the pressure is double low loss refrigerant, otherwise the system will be shut down.
When the high and low pressures are low, there are two possibilities: [low temperature freezer]
(1) The system is blocked, the blocked part will produce throttling, and the throttling part will have a significant temperature difference, and the problem can be found by hand.
(2) The leakage of refrigerant leads to insufficient refrigerant. This situation is relatively common. At this time, a low-temperature chiller detector must be used to find out the leaking location and perform replacement.
3. Low pressure, high pressure, low pressure, replace the compressor.
When the low pressure of the low temperature chiller system is higher than normal with the low temperature chiller pressure gauge, but the high pressure is lower than normal, the chiller refrigeration at this time absolutely cannot achieve the effect of the normal low temperature chiller. The reason is likely to be the wear and tear in the low-temperature chiller pump, resulting in a drop in power. At this time, it is often necessary to replace the compressor to solve the problem.
4. There is water vapor in the meter shake system, so the evacuation must be more thorough.
When the low-temperature chiller system is working, if the pressure gauge needle keeps shaking, it means that the system has moisture. To solve this problem, the vacuum must be re-evacuated, and the time must be no less than 15 minutes. If necessary, the drying bottle must be replaced to completely drain the water in the system.
Tips for troubleshooting the refrigeration system of low-temperature chillers
Subscribe to relevant news content?
Subscription
Unsubscription
Recent related posts
08/14/2020
Tips for troubleshooting the refrigeration system of low-temperature chillers
Regular maintenance work for the low-temperature chiller, while troubleshooting the refrigeration system of the low-temperature chiller is also very important.
08/14/2020
Three commonly used monitoring indicators for refrigeration compressor lubricants
The lubricating oil used in the compressor is very critical, and the detection of lubricating oil and its replacement cycle are also closely related to the process control in the production process.
08/14/2020
The working principle of laser chiller and installation precautions
Laser chiller products have the characteristics of outstanding cooling effect and low cost of cooling work. Before installing and using laser chillers, first require relevant staff to be familiar with the performance of the equipment
08/14/2020
The similarities and differences between open and water-cooled box chillers
Everyone knows that the classification of chillers is diverse and complex. It is mainly divided into two types: air-cooled chillers and water-cooled chillers. Then subdivided further down.
08/14/2020
The refrigeration device is prone to failure and the reason
Among the failures of refrigeration equipment, failures caused by "leakage" and "blocking" are the most common.
08/14/2020
The reason why the fan of air-cooled chiller does not run
In many areas where water sources are lacking, or air-cooled chillers for cooling and cooling of supporting machinery and equipment, after several years of use, such and other small failures may occur.
08/14/2020
The difference between oil cooler and other coolers
An oil cooler is a heat exchanger that uses air to cool hot fluid. Like other coolers, rust scale will appear. The rust scale appears mainly because the cooling water contains a large amount of calcium, magnesium ions and acid carbonates.
08/14/2020
The difference between independent and non-independent refrigeration units
The cold storage is a special place dedicated to refrigeration, and now it is mainly used to keep food fresh. With the increasing requirements for the freshness of food, the use of cold storage is gradually increasing.
08/14/2020
The detection of the power supply voltage of the chiller
Industrial chiller units are widely used. Where there is industry, chiller equipment is required, such as: chemical chillers, electroplating chillers, food chillers, electronic processing chillers, mold chillers, printing chillers, etc.,
08/14/2020
The correct way to open the refrigerated truck for summer maintenance
With the advent of summer, the maintenance of refrigerated trucks is becoming more and more important. In order to prevent the high temperature in summer from damaging the surface of the refrigerated truck,
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
US$2307.69
Panasonic Servo Motor MHMF022L1V2M
US$653.85
Honeywell Solenoid Valve VE4025B1045
US$334.62
ROTEN Mechanical Seal 8E5K-22-X
US$384.62
/2023/P+F-PEPPERL+FUCHS-Encoder-RHI58N-0BAK1R61N-02000/P+F-PEPPERL+FUCHS-Encoder-RHI58N-0BAK1R61N-02000.jpg)
BENNIC Capacitor 35V 680UF
US$0.10
