NSK Servo Drive ESB-YSB3040ABA02-02

11/22/2022

What are Centrifugal Fans Used for?

The centrifugal fan is a device that relies on the input mechanical energy to increase the pressure of the air and discharge the air.

08/07/2020

Knowledge points of HVAC cold and heat source design

1.The design position of the pump in the system: Generally speaking, the chilled water pump should be located at the front end of the chiller, and the chilled water coming back from the end is pumped back to the chiller through the chilled water pump;

06/14/2020

Why does the refrigeration compressor frost and the solution!

Why does the refrigeration compressor frost and the solution! 1. The frost on the compressor return air port indicates that the temperature of the compressor return air is too low, so what will cause the compressor return air temperature to be too low? 器2䀀
ￜ皥
䖒皦즠Ʋ嫜ི㲈Ʋ
䌁皦
ᮔDž༬皧嫦ིЀ呄ᠾ鹨់༹皧
ࠄ
00령ꐱ댁珵뛐珵Љ
䕄ྦ￿￿뤂ᐱ뚜珵ᴴᏩ呄ᠾ퍘ᒥ鹨់ᩄꋔྦ
瑉浥巠皱㙲皦抐皱巠皱੨皦柘皱ￜ皥
ب巠皱㙲皦忈皱੨皦柘皱
즠Ʋǜ勁皦즠ƲبǜV /펔B䌁皦
ᮔDž'鱤džၜ먢䇨珵呈ᠾ뤂ᐱ⿇⬿먲僧ᐱ㥲ᐲ�僬㣢ᐲᠾ
랖僧ӄ識�僬㣢ᐲ臆S㥲ᐲᬄğ識理艏S杴 識杴 㥲ᐲ

09/22/2020

Compression and delivery of air compressor

The compressor can convert the mechanical energy of the motor or internal combustion engine into the pressure of compressed air. Air compressors are divided into two categories: reciprocating and rotary. The following figure shows the basic types of compressors:

06/29/2020

How the compressor works

09/06/2020

What are the advantages and characteristics of power frequency screw air compressors

What are the advantages and characteristics of power frequency screw air compressors? 　　 Power frequency screw air compressor adopts high-efficiency host The power frequency screw air compressor adopts the industry-leading screw main engine, high efficiency, low speed, the rotor adopts the third-generation tooth profile

09/11/2020

Bearing and shaft fit tolerance standard

Bearing and shaft fit tolerance standard ①When the bearing inner diameter tolerance zone and the shaft tolerance zone form a fit, the tolerance code originally belonging to the transition fit in the general basic hole system will become an over-win fit, such as k5, k6, m5, m6, n6, etc., but the over-win amount is not Large; when the bearing inner diameter tolerance is matched with h5, h6, g5, g6, etc., it is not a clearance but an over-win fit.

08/04/2020

Several important issues that should be paid attention to when installing and debugging the inverter on site

nverter is an electric energy control device that uses the on-off action of power semiconductor devices to transform industrial frequency power into another frequency.

01/04/2021

energy conversion and management

Performance improvement of biomass-fueled closed cycle gas turbine via compressor inlet cooling using absorption refrigeration; thermoeconomic analysis and multi-objective optimization By V.Zare Faculty of Mechanical Engineering, Urmia University of T器2䀀
ￜ皥
䖒皦즠Ʋ嫜ི㲈Ʋ
䌁皦
ᮔDž༬皧嫦ིЀ呄ᠾ鹨់༹皧
ࠄ
00령ꐱ댁珵뛐珵Љ
䕄ྦ￿￿뤂ᐱ뚜珵ᴴᏩ呄ᠾ퍘ᒥ鹨់ᩄꋔྦ
瑉浥巠皱㙲皦抐皱巠皱੨皦柘皱ￜ皥
ب巠皱㙲皦忈皱੨皦柘皱
즠Ʋǜ勁皦즠ƲبǜV /펔B䌁皦
ᮔDž'鱤džၜ먢䇨珵呈ᠾ뤂ᐱ⿇⬿먲僧ᐱ㥲ᐲ�僬㣢ᐲᠾ
랖僧Ә識�僬㣢ᐲ臆S㥲ᐲᬄğ識理艏S杴 識杴 㥲ᐲ

03/24/2025

PC Airflow Channel Design: the Best Layout of the Case Airflow Channel

The power supply, CPU, chipset, memory, and graphics card in the computer case can generate a lot of heat.