CAST IRON BODY
WITH DOUBLE ACTING PNEUMATIC ACTUATOR - CAST IRON DISC
Liner:DG375XE68 EPDM
OMAL Butterfly Valve Item 375-DG375XE68
People who bought this item also viewed
TTO Mechanical Seal 34×46×8
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
CKD Solenoid Valve 4GD230-C4-E2C-3
AirTac Solenoid Valve 5V310-10
ABB Circuit Breaker 10133757
ISA Resistor SMK-R100-1.0
Nachi Proportional Valve EOG-G01-P1-11
DANHI Air Cylinder SCDGB40-120
Recent related posts
-
06/14/2020
What are the causes of frost in refrigeration compressors
1. The opening of the thermal expansion valve is too large, or the installation of the temperature sensor is incorrect and the fixing is not firm or loose. The main reason is that the temperature sensor may feel the temperature too high in this case, resu 器2 䀀 ᅵ皥 䖒皦즠Ʋ奌ི 㲈Ʋ 䌁皦 ᮔDž
-
03/02/2021
Control mode of servo motor
Torque control: the torque control mode is to set the external output torque of the motor shaft through the input of external analog quantity or the assignment of direct address. For example, if 10V corresponds to 5nm, when the external analog quantity is set to 5V, the output of the motor shaft is 2.5nm: if the load of the motor shaft is lower than 2.5nm, the motor will rotate forward, and when the external load is equal to 2.5nm
-
09/09/2020
Basic knowledge of gas compressor and its role in various fields
1.Compressor power and pressure: 1. The shaft power of the compressor is the sum of the indicated power and the friction power. The indicated power is the power directly consumed by compressed gas, the friction power is the power consumed by overcoming mechanical friction, and the shaft power of the compressor is the power used to select the drive motor.
-
09/14/2020
Common troubleshooting methods for twin screw compressors
Common troubleshooting of twin screw compressor 1. Trouble phenomenon The exhaust temperature of the unit is high (over 100 degrees) The coolant level of the unit is too low (should be visible in the oil glass but not more than half) Dirty oil cooler
-
09/14/2022
How Does a Hydraulic Drive Motor Work?
hydraulic motor is an actuating element of the hydraulic system, which converts the hydraulic pressure energy provided by the hydraulic pump
-
09/14/2020
What is an air compressor
The machine used to generate compressed air is also called compressed air machine, also called air compressor, or air compressor for short. The motor directly drives the compressor to make the crankshaft produce rotational movement, drive the connecting rod to make the piston produce reciprocating motion, and cause the cylinder volume Variety.
-
08/23/2020
Why does the cooler temperature drop slowly
1. The cold storage has a large loss of cold due to poor heat insulation or sealing performance. Poor thermal insulation performance is due to insufficient insulation thickness of pipes, warehouse insulation walls, etc.,
-
06/14/2020
Five methods for leak detection in refrigeration systems
Five methods for leak detection in refrigeration systems The leak detection of the refrigeration system of the air conditioner includes the leak detection of components such as the refrigeration compressor, condenser, evaporator, filter drier, capillary 器2 䀀 ᅵ皥 䖒皦즠Ʋ奌ི 㲈Ʋ 䌁皦 ᮔDž༬皧奖ིЀ 呄ᠾ鹨់༹皧 ࠄ 00령ꐱ댁珵뛐珵Љ 䕄ྦ 뤂ᐱ뚜珵 ᴴᏩ呄ᠾ퍘ᒥ 鹨់ᩄ ꋔྦ 瑉浥 巠皱㙲皦抐皱 巠皱 ੨皦柘皱 ᅵ皥 ب 巠皱㙲皦忈皱 ੨皦柘皱 즠Ʋǜ 勁皦즠Ʋب ǜ V / 펔B䌁皦 ᮔ
-
04/18/2022
How to Properly Ground The Electromagnetic Flowmeter Under Different Installation Conditions?
Because the output signal of the sensor is very small, it is usually only a few millivolts. In order to improve the anti-interference ability of the instrument, the zero potential in the input circuit must be grounded
-
09/14/2020
Analysis of common failures of air-cooled compressors (1)
There are three common failures in the main components of air-cooled compressors: 1. Failure of the gas circuit system 2. Failure of the oil circuit system 3. Failure of the transmission mechanism. Do some system analysis below