SCHNEEBERGER Linear Guideway BMW15F-G3V1
People who bought this item also viewed
SCHNEEBERGER Linear Guideway MRD45-G2V2
HIWIN Linear Guideway HGW35HCC
NSK Linear Guideway SAH20BN
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
Daikin Compressor JT125B-NFYE
Tecumseh Compressor AJA5519EXV
OMEGA Pressure Gauge DPG1000B-30V100G
Dwyer Switch L6EPS-S-S-3-O
Panasonic Servo Motor MSMD041S1B
Schneider Circuit Breaker LV429833
Recent related posts
-
07/13/2020
HVAC Innovative products and series of Danfoss commercial compressors
Hello everyone, today I will introduce you to Danfoss' high-temperature compressors.The refrigeration capacity of this series of scroll compressors ranges from 2 to 10 tons, and can be used in parallel. The compressor is divided into three platforms-household, small business and light business. Other features include: two frequencies, 450 kinds of codes.
-
08/19/2020
Installation and debugging of thermal expansion valve in refrigeration equipment
The correct installation of the thermal expansion valve will also affect the performance of the refrigeration device. Before installation, check whether the expansion valve is in good condition, especially the temperature sensing mechanism.
-
06/13/2020
Knowledge of maintenance of air energy heat pump
Knowledge of maintenance of air energy heat pump The air energy water heater is composed of an outdoor unit and an insulated water tank. The outdoor unit is called an air energy heat pump unit.
-
08/19/2020
Selection and design of cold storage doors
Under normal circumstances, the cold storage door as one of the cold storage equipment only accounts for less than 10% of the entire system cost. After the entire system is put into use, it has almost become the "front" of the entire system.
-
09/05/2020
The problem of motor inefficiency
The test standards promulgated by the International Electrotechnical Commission IEC (hereinafter referred to as IEC) make it possible to evaluate the energy efficiency of motors.
-
10/25/2021
Use of Baumer Encoder HMG11 and HOG10 in Iron and Steel Smelting Industry
Inside the noisy iron and steel smelting workshop, sparks flare and machines roar, crane weighing hundreds of tons slowly moves blast furnaces filled with molten iron from one station to the next.
-
09/23/2020
Automatic control scheme for multiple adsorption dryers and air compressors
With the development of modern industry and the improvement of automation level, various industries have higher and higher requirements for air supply, purification level, automatic control, and continuous and reliable air supply of air compressor stations.
-
06/13/2020
York refrigeration compressor maintenance
York refrigeration compressor maintenance, general maintenance: In order to ensure long-term, trouble-free operation of the compressor, proper maintenance is important. It is essential for good compressor operation
-
07/29/2020
Nine refrigerant leakage locations and solutions
There are many welds on the left and right sides of the evaporator, and there may be more leaks. The leak of the newly installed air conditioner is mainly due to the poor welding skills of the employees of the air conditioner manufacturer.
-
06/19/2020
What are the causes of air conditioning trip
What are the causes of air conditioning trip 1. The contradiction between the rated current of the air conditioner and the current carrying capacity of the wire. Here are two formulas involved: ①The rated current of air conditioner I=P÷U ÷power factor, the power remains unchanged, the smaller the voltage, the greater the current required. ② The current carrying capacity of the wire I=U÷R, the voltage is proportional to the current. So when the power supply voltage is normal, we must consider the line voltage drop. The longer the line, the greater the resistance, the greater the voltage drop, and the smaller the output current at the end. However, because the power of the load remains unchanged, the voltage becomes smaller, and the current that needs to be output will be larger. At this time, the wire is forced to overload, and the time will cause heating, and eventually cause the tripping of the open circuit. Some friends said that the heat of the wire will not cause the tripping of the circuit breaker. In fact, the manufacturer of the air switch has made it clear in the relevant manuals that the heat of the wire will cause the air switch to trip. Because the wire heats up, the crimp terminal will also heat up, and the resistance will become larger and larger. The larger the resistance, the greater the current consumption, and the hotter it will be, a vicious cycle. 2. Leakage During the daily maintenance work, we will encounter the situation that the air circuit trips due to the leakage of electricity. At least I have not experienced it once or twice. Regardless of the leakage of the neutral line or the leakage of the live line, a long time will cause the circuit breaker to trip. Why does the electric leakage cause the MCB to trip? There are two situations. ① Good grounding. At the beginning, the leakage current was not large, and as time went by, the leakage current became larger and larger, and eventually evolved into a short circuit to ground, unable to close. ②There is no ground wire. If the equipment is not connected to the protective ground, when the wire leaks to the equipment, it is equivalent to adding a large shunt resistance. Like this problem, if the air conditioner does not have a ground wire, when the wire leaks to the air conditioner, the air conditioner is a very large shunt resistor and will consume a lot of current. Eventually, the wire will heat up or trip open. How to determine whether the trip caused by the above two aspects can be done with a clamp ammeter. ① Measure the voltage at the input and output to see if there is a significant change in voltage drop. ②Measure whether the output current exceeds the standard. So my suggestion is: first measure the supply voltage to see if it is within the allowable fluctuation range. Then measure the current to see if it exceeds the rated ampacity of the wire. Finally, check the data one by one according to the measured data to find out the reason.