Schneider Circuit Breaker LV430683

09/08/2020

Teach you how to understand the energy-saving EMC of the air compressor system

Before the article starts, let's sort out the basic characteristics of contract energy management services (EMC): 　　 Use the saved energy cost (energy saving benefit) to pay the investment cost

06/14/2020

The reason for the frost on the compressor air inlet is here!

The reason for the frost on the compressor air inlet is here! Frost on the air inlet of the cold storage compressor is a very common phenomenon in the refrigeration system. Under normal circumstances

01/12/2021

Which is better, Copeland compressor and Mitsubishi compressor

Copeland compressor Copeland compressors are divided into L, C, 3S, 4S, 6S series air-cooled compression condensing units, which can be used as the main component of various refrigeration devices, used in various freezing and refrigeration equipment, acc器2䀀
ￜ皥
䖒皦즠Ʋ奌ི㲈Ʋ
䌁皦
ᮔDž༬皧奖ིЀ呄ᠾ鹨់༹皧
ࠄ
00령ꐱ댁珵뛐珵Љ
䕄ྦ￿￿뤂ᐱ뚜珵ᴴᏩ呄ᠾ퍘ᒥ鹨់ᩄꋔྦ
瑉浥巠皱㙲皦抐皱巠皱੨皦柘皱ￜ皥
ب巠皱㙲皦忈皱੨皦柘皱
즠Ʋǜ勁皦즠ƲبǜV /펔B䌁皦
ᮔDž'鱤džၜ먢䇨珵呈ᠾ뤂ᐱ⿇⬿먲僧ᐱ㥲ᐲ�僬㣢ᐲᠾ
랖僧Җ識�僬㣢ᐲ臆S㥲ᐲᬄğ識理艏S杴 識

08/09/2020

Solutions to common failures of refrigeration control systems

1. The solenoid valve coil is burnt out<br></br> 　　 Phenomenon is that there is no heat in the low-voltage negative electromagnetic coil shell, and it is short-circuited with a multimeter RX10. The solution is to replace the same type of coil separately.

06/29/2020

Suggestions for troubleshooting of compressor with liquid start

04/19/2022

How to Properly Ground The Electromagnetic Flowmeter Under Different Installation Conditions?

Because the output signal of the sensor is very small, it is usually only a few millivolts. In order to improve the anti-interference ability of the instrument, the zero potential in the input circuit must be grounded

11/16/2022

How to Fix an Industrial Fan?

Industrial fans can effectively control the air circulation in industrial production workshops. However, industrial fans can also fail due to improper use and prolonged use.

03/03/2021

Control mode of servo motor

Torque control: the torque control mode is to set the external output torque of the motor shaft through the input of external analog quantity or the assignment of direct address. For example, if 10V corresponds to 5nm, when the external analog quantity is set to 5V, the output of the motor shaft is 2.5nm: if the load of the motor shaft is lower than 2.5nm, the motor will rotate forward, and when the external load is equal to 2.5nm

08/14/2020

Cold storage design acceptance installation standards

A newly built cold storage, when it’s time for acceptance, it will definitely be annoying. How to check and accept to ensure quality and quantity is actually not as troublesome as you think.

09/04/2020

Main permanent magnet materials commonly used in oil-free screw air compressor motors

Permanent magnet materials commonly used in oil-free screw air compressor motors include sintered magnets and bonded magnets. The main types are AlNiCo, ferrite, samarium cobalt and neodymium iron boron.