Voltage: three phase
Input: AC 3PH 200-240V 50-60HZ
Output: AC 3PH 0-240V 0-400Hz 45A
Rated capacity: 17KVA
Yaskawa VFD Frequency Converter CIMR-F7A2011
People who bought this item also viewed
Yaskawa VFD Frequency Converter CIMR-F7A2015
Yaskawa VFD Frequency Converter CIMR-F7A4220
Lenze VFD Frequency Converter E82EV751-4C040
Mitsubishi Servo Motor HA-FF053
HITECH HMI PWS6620S-P
LS Mecapion Encoder S30-4-500VL
Johnson Controls Actuator M9220-AGC-3
COSEL Power Supply LFA150F-24-SR2
Honeywell PLC 900C70-0360-00
Winyao NIC Card WY545F
INFINEON IGBT Module BSM100GAL120DN2K
SEHEY Battery NP33-12
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
Danfoss Solenoid Valve CoilBG115DS
Siemens Circuit Breaker 5SL6202-8CC
Festo Air Cylinder DGSL-10-10-PA
SAMYOUNG Capacitor 200V 4.7UF
Recent related posts
-
06/29/2020
Treatment of frost in crankcase when compressor head frost is serious
Treatment of frost in crankcase when compressor head frost is serious The frost on the cylinder head is caused by a large amount of wet steam or refrigerant sucked into the compressor. The main reasons for this situation are:
-
05/11/2022
Mitsubishi air conditioner E1, E2, E3, E4, E5, E6 and other faults, how to troubleshoot and repair?
Whether there is a fault in the indoor and outdoor units can be known by the access code of the remote control, the content of the green LED
-
03/07/2021
AC servo driver wiring precautions
For signal line and encoder input line, please use shielded wire. Wiring length: the length of signal line from NC to AC servo driver is less than 3m, and the length of input line from AC driver to encoder is less than 20m. The ground wire should be thick wire as far as possible. According to the third grounding standard (grounding resistance < 100 Ω), one point grounding method should be adopted to connect the ground wire. If the motor and the machine tool are insulated, the motor should be grounded.
-
08/29/2020
How to achieve zero failure of enterprise compressor equipment
How to achieve zero failure of enterprise compressor equipment
-
06/29/2020
Analysis of the cause of excessive suction temperature of compressor
Analysis of the cause of excessive suction temperature of compressor The high suction temperature is mainly due to the increase of superheat of suction. Note that high suction temperature does not mean high suction pressure, because the suction is superheated steam. Under normal circumstances, the compressor cylinder head should be half cold and half hot. If the suction temperature is too high, the cylinder head will all heat up.
-
06/27/2020
Refrigerator compressor working principle, wiring diagram, structure
The core component of the refrigerator is the compressor. If there is no compressor with good quality and technology, it is not a good refrigerator. At present, many products on the market advertise the use of high-quality compressors, so which compressor brands are in China, and which failures are prone to occur? I will introduce you one by one in the following!
-
08/02/2020
Why do some compressors have to soft start
We know that the motor's direct starting current is 4 to 7 times the rated current, so if the power of the motor is relatively small, then the impact on the grid is not great, we allow it to start directly, generally the motor power is allowed below 7.5KM Started directly
-
02/16/2023
Installation and Maintenance of Gearboxes
When you select gearbox model, four factors should be given comprehensive consideration.
-
07/07/2020
Overnight, refrigerant leaked light, guess where is the problem
Overnight, refrigerant leaked light, guess where is the problem After receiving notification from VIP customers, they went to a concrete mixing plant in the suburbs to repair an air conditioner.
-
12/03/2023
Notebook Cooling: Function Analysis of Thermal Grease, Heat Pipe and Cooling Fins
In the cooling module of the notebook, the three most critical elements are the heat pipe, the cooling fan and the cooling fins, and there are also elements used to improve the contact area and heat transfer efficiency between them.