Fluid: Air(to be filtered by 40u m filter element)
Mounting type: Basic FA FB CA CB CR LB TC FTC TCM1 TCM2 Operating pressure: 0.15 to 1.0 Mpa(22 to 145psi)(1.5 to 10.0bar) Proof pressure: 1.5MPa(215psi)(15bar)
Temperature(degrees Celsius): -20 to 70
Speed range(mm per second): 30 to 800 or 30 to 500
Cushion type: Variable cushion
Bore size:200mm
Stroke:600mm
Magnet:with magnet
AirTAC Air Cylinder Pneumatic SAI200X600SDouble acting type
People who bought this item also viewed
MINDMAN Air Cylinder MCMB-11-40-75-A
AirTAC Air Cylinder ACKR40X90
AirTAC Air Cylinder BSC50X75S
AirTAC Air Cylinder SC32X50
AirTAC Air Cylinder ACE32X125
Festo Air Cylinder DNC-32-700-PPV-A
MINDMAN Air Cylinder MCJT-12-32-8
CKD Air Cylinder RCC2-00-32-35-L
CKD Air Cylinder BHA-03CS1-T2H-D
ELCO Encoder EI100P30-L5PR-1000
KITZ Actuator BZ-5
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
Ebmpapst Fan A2D250-AA02-02
Fanuc Servo Drive A06B-6134-H202#A
SHAKO Air Cylinder PC16B100
Beckhoff Module EL3124
Recent related posts
-
06/14/2020
Introduction of internal control elements of industrial chillers
Introduction of internal control elements of industrial chillers Chiller is a kind of water cooling equipment, which can provide constant temperature, constant current and constant pressure cooling water equipment. Its working principle is to inject a ce ﰸ2
-
07/11/2020
Working flow chart of screw air compressor
Working flow chart of screw air compressor In the first step, the air compressor sucks the surrounding air through the air filter to make it enter the compression host.
-
08/15/2020
How to operate the cold storage distribution box during cold storage installation
In the process of cold storage installation, the use of cold storage power distribution boxes is a very important content, but most people are not very familiar with the normal operation of cold storage power distribution boxes.
-
06/14/2020
The main cause of the burning of refrigeration compressor windings
The damage of the motor coil is mainly manifested as the destruction (short circuit) and open circuit of the stator winding insulation. After the stator winding is damaged, it is difficult to be found in time, which may eventually cause the winding to bur 器2 䀀 ᅵ皥 䖒皦즠Ʋ煔क़ 㲈Ʋ 䌁皦 ᮔDž༬皧煞क़Ѐ 呄ᠾ鹨់༹皧 ࠄ 00령ꐱ댁珵뛐珵Љ 䕄ྦ 뤂ᐱ뚜珵 ᴴᏩ呄ᠾ퍘ᒥ 鹨់ᩄ ꋔྦ 瑉浥 巠皱㙲皦抐皱 巠皱 ੨皦柘皱
-
04/27/2022
How to Test Your Surge Protection Device?
Surge protection devices protect our electronic equipment from the impact of surge and lightning which will occur without warning at any time.
-
09/11/2020
Hanbell screw compressor oil replacement operation specification
Maintenance and operation instructions for the refrigerating oil of the screw refrigerant compressor of Hanbell 1. The role of lubricating oil:
-
06/14/2020
The reasons for the high temperature of the compressor discharge are
The reasons for the high temperature of the compressor discharge are (1) The clearance in the compressor cylinder is too large; (2) The suction and exhaust valves and piston ring of the compressor are damaged; (3) The compressor safety bypass valve 器2 䀀 ᅵ皥 䖒皦즠Ʋ奌ི 㲈Ʋ 䌁皦 ᮔDž༬皧奖ིЀ 呄ᠾ鹨់༹皧 ࠄ 00령ꐱ댁珵뛐珵Љ 䕄ྦ 뤂ᐱ뚜珵 ᴴᏩ呄ᠾ퍘ᒥ 鹨់ᩄ ꋔྦ 瑉浥
-
11/13/2023
9 Types of Fan Bearing Comparison: How to Have Both Quietness and Longevity?
Quietness and longevity have always been two very important performance parameters in the PC heat dissipation field, and the fan can be said to be the biggest source of noise inside the entire computer case.
-
08/06/2020
Principles that need to be followed when using antifreeze in industrial chillers
Principles that need to be followed when using antifreeze in industrial chillers<br></br> The role of antifreeze for industrial chillers is to prevent expansion and cracking of heat exchangers, pipes or engine cylinder blocks due to the freezing of the coolant.
-
06/30/2020
You should know the normal working condition of the compressor in the cold storage
You should know the normal working condition of the compressor in the cold storage 1. The suction temperature of the compressor should be 5-15℃ higher than the evaporation temperature.