You should know the normal working condition of the compressor in the cold storage

refrigeration compressor，compressor,Mitsubishi Compressor,Bristol Compressor，HITACHI Compressor，Danfoss compressor

1. The suction temperature of the compressor should be 5-15℃ higher than the evaporation temperature. 　　 2. The discharge temperature of the compressor R22 system must not exceed 150℃. 　　 3. The oil temperature of the compressor crankcase must not exceed 70℃. 　　 4. The suction pressure of the compressor should correspond to the evaporation pressure; 　　 5. The compressor discharge pressure R22 system must not exceed 1.8MPa. 　　 6. The oil pressure of the compressor is 0.12-0.3MPa higher than the suction pressure. 　　 7. Cooling water volume and water temperature, the outlet temperature of the condenser should be 2-5℃ higher than the inlet temperature. 　　 8. Always pay attention to the oil level of the compressor crankcase and the oil return of the oil separator. 　　 9. The compressor should not have any knocking sounds, and all parts of the body should be normal. 　　 10. The condensing pressure should not exceed the compressor discharge pressure range.

Recent related posts

06/30/2020

You should know the normal working condition of the compressor in the cold storage

You should know the normal working condition of the compressor in the cold storage 1. The suction temperature of the compressor should be 5-15℃ higher than the evaporation temperature.

06/30/2020

What are the causes of compressor overheating

What are the causes of compressor overheating Some causes of compressor overheating: high return air temperature, large motor heating capacity, high compression ratio, high condensing pressure, and improper refrigerant selection.

06/29/2020

Semi-closed piston refrigeration compressor 4SJH-3000

Semi-closed piston refrigeration compressor 4SJH-3000 Features of semi-hermetic piston compressor 4SJH-3000: 1. Light in size and small in space 2. Suitable for R12, R22 and R502, with a wide range of applications

06/29/2020

What are the causes treatment and prevention methods of compressor liquid blow

What are the causes, treatment and prevention methods of compressor liquid blow Liquid blow means that the refrigerant liquid or wet steam is sucked into the compressor by the compressor due to failure or insufficient absorption of heat, which is called liquid blow. First, the main reasons are as follows:

06/29/2020

Dehumidification technology with dual cold sources for clean air conditioners

Dehumidification technology with dual cold sources for clean air conditioners Compressors are used in many industries and in life, such as air conditioners that we cannot do without in summer. The air conditioner has a clean function and adopts dual cold source deep dehumidification technology. Composed of compressor, evaporator, condenser, refrigeration circuit, two-stage relay with cold water coil, can effectively achieve a minimum supply air dew point temperature of 8 ℃;

06/29/2020

The role of freezing oil in screw refrigeration compressor

The role of freezing oil in screw refrigeration compressor The role of lubricating oil: 　　 1) A dynamic seal is formed between the screw and the compression chamber and the male and female screws to reduce refrigerant leakage from the high-pressure side to the low-pressure side during the compression process.

06/29/2020

How to deal with compressor stuck cylinder

How to deal with compressor stuck cylinder The compressor jamming cylinder means that the shaft of the compressor is stuck, and the compressor cannot rotate at this time. The cause of the compressor jamming cylinder is either the lack of refrigeration oil, insufficient lubrication and increased friction, or the presence of dust or impurities in the pipeline, which causes the moving surface to be stuck, or the pure mechanical failure causes the compressor to be stuck.

06/29/2020

Precautions for the use of screw air compressor oil

Precautions for the use of screw air compressor oil Note on the use of screw air compressor oil: It is forbidden to mix air compressor oils of different brands and grades. The old oil must be drained when replacing. It is strictly forbidden to add or filter and reuse.

06/29/2020

Too small selection results in insufficient compressor displacement

Too small selection results in insufficient compressor displacement Many users just start not knowing the specific gas consumption of their own production, so they blindly select the model according to their own estimates, resulting in exhaust pressure not coming up, below the rated exhaust pressure, which cannot meet the normal gas consumption of the factory.

06/29/2020

Analysis of the cause of excessive suction temperature of compressor

Analysis of the cause of excessive suction temperature of compressor The high suction temperature is mainly due to the increase of superheat of suction. Note that high suction temperature does not mean high suction pressure, because the suction is superheated steam. Under normal circumstances, the compressor cylinder head should be half cold and half hot. If the suction temperature is too high, the cylinder head will all heat up.