BANDO Belt A-390
People who bought this item also viewed
COKERY Belt B130
SYNCHROFLEX Belt T 5-255
SYNCHROFLEX Belt AT 5-340
ESBAND Belt PU11 1470×22×3.0
Panasonic Servo Motor MSME011G1B
JSCC Reduction Drive 90YR90DV22
KMC Industrial Chain silver pink X10
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
Schneider Sensor XUX1ANBNT16
OMRON Power Supply S8FS-C35048J
TAKEX Sensor FX205
Adleepower VFD Frequency Converter AP4G3-75
NORGREN Air Cylinder RM/8026/M/220
Recent related posts
-
09/16/2020
Quality Reliability Test and Improvement of the Main Body of Filter Element
Abstract: Combining with the actual situation of the oil production site, through a comprehensive analysis of the manifestations of filter element failure, the filter element material, main tube wall thickness, and water hole density are used as the three main reliability factors that affect the life of the filter element on-site, and the pole is reasonably determined.
-
06/14/2020
Cold storage equipment installation and commissioning
Installation of refrigeration compressor unit in cold storage: The condensing unit should avoid installing in high temperature environment, and the outdoor awning should be installed to avoid rain or direct sunlight. The air inlet side of the air-cooled c 器2 䀀 ᅵ皥 䖒皦즠Ʋ嫜ི 㲈Ʋ 䌁皦 ᮔDž༬
-
12/15/2021
What Data Can a Human Machine Interface (HMI) Tablet Collect?
Due to the shortage of energy supply, and increasingly significant environmental problems, new energy resources have been gradually known to people. Wind energy is a type of renewable clean energy.
-
07/14/2020
Compressor operation requirements
Compressor operation requirements The first load operation of the compressor is carried out after the empty vehicle operation and purging are completed. The compressor should be operated according to the following requirements:
-
06/20/2020
What are the causes of air conditioning trip
What are the causes of air conditioning trip 1. The contradiction between the rated current of the air conditioner and the current carrying capacity of the wire. Here are two formulas involved: ①The rated current of air conditioner I=P÷U ÷power factor, the power remains unchanged, the smaller the voltage, the greater the current required. ② The current carrying capacity of the wire I=U÷R, the voltage is proportional to the current. So when the power supply voltage is normal, we must consider the line voltage drop. The longer the line, the greater the resistance, the greater the voltage drop, and the smaller the output current at the end. However, because the power of the load remains unchanged, the voltage becomes smaller, and the current that needs to be output will be larger. At this time, the wire is forced to overload, and the time will cause heating, and eventually cause the tripping of the open circuit. Some friends said that the heat of the wire will not cause the tripping of the circuit breaker. In fact, the manufacturer of the air switch has made it clear in the relevant manuals that the heat of the wire will cause the air switch to trip. Because the wire heats up, the crimp terminal will also heat up, and the resistance will become larger and larger. The larger the resistance, the greater the current consumption, and the hotter it will be, a vicious cycle. 2. Leakage During the daily maintenance work, we will encounter the situation that the air circuit trips due to the leakage of electricity. At least I have not experienced it once or twice. Regardless of the leakage of the neutral line or the leakage of the live line, a long time will cause the circuit breaker to trip. Why does the electric leakage cause the MCB to trip? There are two situations. ① Good grounding. At the beginning, the leakage current was not large, and as time went by, the leakage current became larger and larger, and eventually evolved into a short circuit to ground, unable to close. ②There is no ground wire. If the equipment is not connected to the protective ground, when the wire leaks to the equipment, it is equivalent to adding a large shunt resistance. Like this problem, if the air conditioner does not have a ground wire, when the wire leaks to the air conditioner, the air conditioner is a very large shunt resistor and will consume a lot of current. Eventually, the wire will heat up or trip open. How to determine whether the trip caused by the above two aspects can be done with a clamp ammeter. ① Measure the voltage at the input and output to see if there is a significant change in voltage drop. ②Measure whether the output current exceeds the standard. So my suggestion is: first measure the supply voltage to see if it is within the allowable fluctuation range. Then measure the current to see if it exceeds the rated ampacity of the wire. Finally, check the data one by one according to the measured data to find out the reason.
-
08/21/2020
Analysis of common causes of cylinder jam caused by heat pump compressor
What are the reasons for the jam of the heat pump compressor? Do you guys know? Let’s take a closer look with the editor of okmarts.com today!
-
09/11/2020
Recent market development of air source heat pumps in various countries in the world
The 1997 World Climate Summit in Kyoto, Japan established the reduction of greenhouse gases (GHG), achieving the goal of reducing greenhouse gases by at least 5% below 1990 levels between 2008 and 2012.
-
08/29/2020
SPK Fluid reliable compressed air escort
SPK Fluids is a global supplier that provides highly specialized and engineered solutions, with branches in 35 countries and operations in more than 150 countries around the world.
-
07/13/2020
compressor trading platform
All basic knowledge of screw air compressor The full name of the air compressor is an air compressor; a machine designed according to the working principle of the rotation of the twin screw (also called Yin and Yang rotor) to change the volume of the gas, it can suck in natural air and then complete the work through several internal processes. To discharge compressed air that meets pressure requirements, this machine is called a screw air compressor.
-
09/15/2020
85 pool water level sensor, field lightning protection transmitter
Sensor, field lightning protection transmitter okmarts.com pressure sensor, okmarts.com pressure transmitter, okmarts.com pressure sensor PTH601 uses diffused silicon piezoresistive core or ceramic piezoresistive core, 316 stainless steel structure, mainly suitable for rivers, groundwater levels, reservoirs, water towers and containers, etc. liquid level measurement and control.