Recent market development of air source heat pumps in various countries in the world
The 1997 World Climate Summit in Kyoto, Japan established the reduction of greenhouse gases (GHG), achieving the goal of reducing greenhouse gases by at least 5% below 1990 levels between 2008 and 2012. In order to achieve the goal of the "Kyoto Protocol", there must be a change in energy utilization in the field of man-made environments that occupy most of the primary energy and most of the greenhouse gas emissions.
Recent market development of air source heat pumps in various countries in the world
Recent related posts
-
09/11/2020
Recent market development of air source heat pumps in various countries in the world
The 1997 World Climate Summit in Kyoto, Japan established the reduction of greenhouse gases (GHG), achieving the goal of reducing greenhouse gases by at least 5% below 1990 levels between 2008 and 2012.
-
09/11/2020
Radial bearing
Radial bearing: Rolling bearing mainly used for bearing radial load, its nominal contact angle ranges from 0 degrees to 45 degrees. According to the different nominal contact angles,
-
09/11/2020
Provide compressed air without oil, water and dust
The drying effect is achieved through the principle of pressure swing adsorption. Not only can it be matched with a small air compressor, but it can also meet the needs of local users with special requirements behind the large air compressor, so as to avoid the high air quality requirements of individual points and the high configuration of the entire equipment to save investment.
-
09/11/2020
Oil bath air filter zksg
In the working environment with high dust concentration in the air, the dust removal filter device used in general air compressors is mostly screen-type secondary dust removal paper and fiber material filtration.
-
09/11/2020
Noise analysis and treatment of air compressor
Noise analysis and treatment of air compressor A compressor manufacturer's statement: The noise level guarantee is +3dBA, which means that its noise level will be twice or one half of the declared noise level.
-
09/11/2020
Maintenance of screw air compressor
1. Maintenance of intake air filter element. The air filter is a component that filters out air dust and dirt. The filtered clean air enters the compression chamber of the screw rotor for compression. Because the internal clearance of the screw machine only allows particles within 15u to filter out.
-
09/11/2020
Inverter companies will transform to personalized services
Recently, the Institute of Industry and Market Research of the Institute of Machinery Industry Information said that my country's inverter market will not be saturated until at least 10 years, and the overall market potential is 120 billion to 180 billion yuan.
-
09/11/2020
Introduction to cleaning and maintenance of temperature control valve of okmarts.com air compressor
The composition of the temperature control valve of okmarts.com air compressor: The temperature control valve is composed of valve body, valve core, temperature sensing element, spring, etc.:
-
09/11/2020
How to use empirical methods to inspect rolling bearings
How to use empirical methods to inspect rolling bearings Some operators lack the experience in identifying rolling bearings and continue to use them as long as they see no obvious damage to the rolling bearings, causing serious failures later. Some people only need to remove the rolling bearings and replace them without inspection.
-
09/11/2020
How to ensure the stable operation of imported bearings
Generally speaking, pay attention to the following points from the perspective of use: 1. The bearing clearance should be appropriate. If it is too large, it will cause impact, and if it is too small, it will cause poor lubrication and may burn bushes.
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
AirTAC Air Cylinder SCJ32X400-20S
PHOENIX Surge Protection Device D-LAN-19"-24
YUKEN Vane Pump PV2R12-17-47-F-REAA-41
SKF Oil Seal 35X80X12 HMS5 V(FKM)