CARLO Relay RS1A23A2-40
People who bought this item also viewed
SIEMENS Relay 3TK2824-1AL20
JEL Relay S1C-225WDV
Riken Relay RAB-150N
TRIAD Transformer F-282U
Eaton Contactor DILEM-10-G-C(24VDC)
CITEL Surge Protection Device DS42-385
Ferraz Shawmut Fuse PC44UD75V22CTQ
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
HAYWARD Water Pump SP2815*2051
Sanyo Denki Fan 109-374
Contrinex Sensor DW-DS-615-M12
Festo Air Cylinder ADVC-40-40-I-P-A
SMC Ball Valve CDUJB10-15D
Recent related posts
-
07/28/2020
Method and steps to replace the refrigeration compressor
Cut off the power supply: Before replacing the compressor, be sure to cut off the power supply of the unit, otherwise there will be a risk of electric shock.
-
02/23/2023
The Advantages and Disadvantages of Butterfly Valve and Its Installation and Maintenance
Butterfly valve is a kind of valve whose closing part (valve clack or butterfly plate) is a disc and rotates around the valve shaft to open and close.
-
06/20/2020
What are the causes of air conditioning trip
What are the causes of air conditioning trip 1. The contradiction between the rated current of the air conditioner and the current carrying capacity of the wire. Here are two formulas involved: ①The rated current of air conditioner I=P÷U ÷power factor, the power remains unchanged, the smaller the voltage, the greater the current required. ② The current carrying capacity of the wire I=U÷R, the voltage is proportional to the current. So when the power supply voltage is normal, we must consider the line voltage drop. The longer the line, the greater the resistance, the greater the voltage drop, and the smaller the output current at the end. However, because the power of the load remains unchanged, the voltage becomes smaller, and the current that needs to be output will be larger. At this time, the wire is forced to overload, and the time will cause heating, and eventually cause the tripping of the open circuit. Some friends said that the heat of the wire will not cause the tripping of the circuit breaker. In fact, the manufacturer of the air switch has made it clear in the relevant manuals that the heat of the wire will cause the air switch to trip. Because the wire heats up, the crimp terminal will also heat up, and the resistance will become larger and larger. The larger the resistance, the greater the current consumption, and the hotter it will be, a vicious cycle. 2. Leakage During the daily maintenance work, we will encounter the situation that the air circuit trips due to the leakage of electricity. At least I have not experienced it once or twice. Regardless of the leakage of the neutral line or the leakage of the live line, a long time will cause the circuit breaker to trip. Why does the electric leakage cause the MCB to trip? There are two situations. ① Good grounding. At the beginning, the leakage current was not large, and as time went by, the leakage current became larger and larger, and eventually evolved into a short circuit to ground, unable to close. ②There is no ground wire. If the equipment is not connected to the protective ground, when the wire leaks to the equipment, it is equivalent to adding a large shunt resistance. Like this problem, if the air conditioner does not have a ground wire, when the wire leaks to the air conditioner, the air conditioner is a very large shunt resistor and will consume a lot of current. Eventually, the wire will heat up or trip open. How to determine whether the trip caused by the above two aspects can be done with a clamp ammeter. ① Measure the voltage at the input and output to see if there is a significant change in voltage drop. ②Measure whether the output current exceeds the standard. So my suggestion is: first measure the supply voltage to see if it is within the allowable fluctuation range. Then measure the current to see if it exceeds the rated ampacity of the wire. Finally, check the data one by one according to the measured data to find out the reason.
-
12/15/2023
Troubleshooting Loud Server Fans: Causes and Solutions
In the realm of technology, servers serve as the backbone of numerous industries, powering everything from websites to data centers.
-
08/15/2020
Solution to the condensing pressure of the chiller refrigeration system
1. The condenser of the chiller is dirty Computer room chillers generally use air-cooled condensers, which are composed of multiple sets of coils, and fins are added to the coils to increase the heat transfer area on the air side.
-
06/21/2022
10 Common Types of Transformer?
You might have come across various types of transformers in your daily life either knowingly or unknowingly. Different types of transformers are explained in brief in this article.
-
01/29/2022
3 Reasons for Using Pressure Transmitters in HVAC Systems
Transmitters play an indispensable role in most applications in HVAC (Heating, ventilation, and air conditioning) systems, which can maintain a suitable indoor temperature
-
11/24/2021
A Quick Look at HMI Touch Screen in Industrial Scenes
In modern society, mobile phone is almost a necessity for everyone. When your mobile phone is not around, you may easily feel anxious as if something is missing, which is called nomophobia.
-
06/16/2020
Danfoss introduces TTH/TGH compressor for higher lift applications
Danfoss introduces TTH/TGH compressor for higher lift applications Danfoss, the world’s leading manufacturer of oil-free compressor technology, offers a new range of compressors that can operate in demanding high lift applications. The new Danfoss Turb 器2 䀀 ᅵ皥 䖒皦즠Ʋ奌ི 㲈Ʋ 䌁皦 ᮔDž༬皧奖ིЀ 呄ᠾ鹨់༹皧 ࠄ 00령ꐱ댁珵뛐珵Љ 䕄ྦ 뤂ᐱ뚜珵 ᴴᏩ呄ᠾ퍘ᒥ 鹨់ᩄ ꋔྦ 瑉浥 巠皱㙲皦抐皱 巠皱 ੨皦柘皱 ᅵ皥 ب 巠皱㙲皦忈皱 ੨皦柘皱
-
09/01/2022
What is a Magnetic Contactor?
In many cases, the magnetic contactor is simply referred to as a contactor. It is an electrical appliance that uses the current flowing through the coil to generate a magnetic field to close the contacts to control the load in industrial electricity.