Application of compressed air filter drier in mold manufacturing
Application of compressed air filter drier in mold manufacturing
Conditions for manufacturing molds
1. Environmental conditions
Temperature: During the whole process of manufacturing male and female molds, the same ambient temperature should always be maintained, that is, 21~28℃.
Humidity: Humidity has a great influence on the curing of gel coat and resin. The ideal humidity range is 40~60. If the relative humidity exceeds 65 when making the mold, you should wait until the appropriate production conditions before construction, especially in southern and coastal areas, where the humidity is relatively Big, more careful.
2. Clean workshop
It is impossible to manufacture high-quality molds in a dirty environment. The manufacturing area of the male and female molds should be highly clean and must have higher maintenance and management standards than the product production area. Therefore, at the beginning of mold manufacturing, it should be done in advance. Good dust removal and cleaning work in the mold manufacturing area.
3. Clean compressed air
Pure and dry air supply is another element for manufacturing high-quality molds. If there is a small amount of water or oil in the air duct, a large number of pinholes and pits will appear on the surface of the mold gel coat. For this reason, a lot of labor is required to repair, so the quality of the mold will be greatly affected. The air compressor needs to be placed in a good environment and equipped with an effective Ruishiji compressed air dryer and a high-precision compressed air multifunctional filter for water removal, oil removal and dust removal.
4. Selection of raw and auxiliary materials
The selection of high-quality raw and auxiliary materials is an important condition for manufacturing high-quality molds. The cost of raw and auxiliary materials used to manufacture molds only accounts for a small percentage of the total cost, and it is not possible to try to save and use product resins or materials that have expired and inferior materials.
5. Develop a reasonable mold making schedule
Arranging a suitable mold making schedule is one of the factors that make a good mold. Regardless of whether the traditional layup method or the new low-shrinkage system is used, the time required is determined by the chemical properties of these raw and auxiliary materials. Any attempt to take shortcuts or accelerate the process will adversely affect the quality of the mold. .
Application of compressed air filter drier in mold manufacturing
Recent related posts
-
09/22/2020
Application of compressed air filter drier in mold manufacturing
Application of compressed air filter drier in mold manufacturing Conditions for manufacturing molds 1. Environmental conditions Temperature: During the whole process of manufacturing male and female molds, the same ambient temperature should always be maintained, that is, 21~28℃.
-
09/21/2020
Improvement of key parts of regenerative refrigerator
Due to its unique structure, many parts, and complicated process, the heat recovery refrigerator is only produced by the standard product factory of Hangyang Technology Co., Ltd. in China. However, due to the fast start-up of the equipment (5-7 minutes for liquid discharge), easy operation and high degree of automation, the products are sold all over the country and exported to foreign countries. It has won unanimous praise from users at home and abroad and has become the flagship product of the factory.
-
09/21/2020
Working principle and usage method of motor bearing grease
Working principle and usage method of motor bearing grease The lubrication of the motor bearing relies on the lubricating oil that is precipitated when the three-dimensional fiber network structure in the grease is broken under the action of shear, forming a layer of lubricating film on the rotating elements of the bearing, the bearing seat and the bearing race for lubrication Effective.
-
09/21/2020
The sealing problem of scroll type automobile air-conditioning compressor
During the mutual movement between the end face of the scroll tooth and the bottom of the scroll plate of the oil-free scroll compressor, the sealing and lubrication function of the end face of the tooth will be affected due to the inability to form an oil film.
-
09/21/2020
The history of industry
China is one of the first countries in the world to invent rolling bearings. According to archaeological relics and data, China’s oldest bearing with the prototype of a modern rolling bearing structure appeared in Xuejiaya Village, Yongji County, Shanxi Province from 221 to 207 BC (Qin Dynasty).
-
09/21/2020
Refrigeration system failure symptoms
Symptoms of refrigeration system failure 1. Detection of pressure and temperature of refrigeration system (1) The pressure concept of the refrigeration system The refrigeration system can be divided into high and low pressure during operation. The high pressure section is from the discharge port of the compressor to before the throttle valve. This section is called the evaporation pressure.
-
09/21/2020
Product development of CFT-303.8 centrifugal chlorine compressor
Hangzhou Hangyang Compressor Co., Ltd. is one of the core enterprises of Hangyang Group. Its leading product is the development and production of various gas-medium compressor products for empty distribution sets and chemical processes (the variety and specifications have reached more than 110 Species);
-
09/21/2020
Noise Control of Ash Removal Air Compressor Room in Thermal Power Plant
The 240 mm clay bricks are closed to eliminate the influence of direct sound on the outside world. The steel window on the other side of the workshop is fixed (not open), and a layer of airtight and fixed sound insulation windows is added on the outside. The distance between the two windows is 100 mm, the sound insulation window uses 8 mm thick glass.
-
09/21/2020
Lubricant knowledge
Lubricating oil knowledge 1. Lubricating oil function Lubricating oil is a liquid lubricant used on various types of machinery to reduce friction and protect machinery and processed parts. It mainly plays the role of lubrication, cooling, rust prevention, cleaning, sealing and buffering.
-
09/21/2020
How to maximize bearing life
How to maximize bearing life In theory, the service life of rolling bearings in centrifugal pumps is 20,000 to 80,000 hours, but the actual life depends on many
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
Parker Coil 481044A5
CKD Air Cylinder SCW-00-63B-250-T0H-D
Banner Light Curtain SLPE25-830P8
Bosch Rexroth Servo Drive TDM 1.2-050-300-W1
NEW-ERA Air Cylinder PPT-SD6M-10-TPQP