Correct handling method of single compressor

Correct handling method of single compressor The handling of a single compressor is very particular and has strict requirements, that is to say, it is not how you want to move it. 　　 The correct way to handle a single compressor is: drag the lower part of the accumulator with one hand, tilt the compressor, and place the other hand on the main casing to support most of the weight. 　　Not only do we need to understand the correct method of handling a single compressor, but also we need to know which methods are not operable: 　　 1. Place a single compressor flat or upside down. 　　 2. Support the weight of the compressor with the accumulator. 　　 3. Hold the suction and exhaust pipes to lift the compressor. 　　In addition, if you think there is anything you need to add, please contact us okmarts.com

Recent related posts

06/30/2020

Correct handling method of single compressor

Correct handling method of single compressor The handling of a single compressor is very particular and has strict requirements, that is to say, it is not how you want to move it.

06/30/2020

Newly manufactured or overhauled compressors should do these inspections

Newly manufactured or overhauled compressors should do these inspections Newly manufactured or repaired compressors should undergo a test drive test. During the test, check:

06/30/2020

Pay attention to keep the compressor lubricating oil clean

Pay attention to keep the compressor lubricating oil clean Why should we pay attention to keeping the compressor lubricating oil clean? This is because the dirty oil of the compressor or the deteriorated lubricating oil will cause a vicious cycle of accelerating the wear of the parts. Therefore, we should clean the lubricant oil of the compressor according to the following requirements:

06/30/2020

Broken suction valve of Bristol compressor

Broken suction valve of Bristol compressor A Bristol compressor is a machine that compresses gas. Generally, the piston compresses gas 1450 times per minute (half-sealed compressor) or 2900 times (full-sealed compressor), that is, the time to complete an intake or exhaust process is 0.02 seconds or even shorter.

06/30/2020

Lubrication method for air conditioner compressor fault maintenance

Lubrication method for air conditioner compressor fault maintenance The specific conditions of the lubrication method for air conditioner compressor fault maintenance are as follows:

06/30/2020

These several compressor failures need our attention

These several compressor failures need our attention In the refrigeration industry, everyone knows that the compressor is the core of the entire ice-making equipment. The quality of a compressor often determines the life of the refrigeration equipment, but no one can guarantee that the entire equipment will not have any problems during use, so It is very helpful for you to know some common faults that occur during the use of the compressor.

06/30/2020

How to deal with the faulty host refrigerant system of the compressor

How to deal with the faulty host refrigerant system of the compressor How to deal with a main engine refrigerant system where the compressor has burnt out or failed is a more serious and technically demanding problem than the production of a new main engine. However, it is often neglected by most of the technicians, and even the wrong concept is replaced if they think that it is broken anyway! It causes some disputes that the compressor quality is poor or others use it improperly.

06/30/2020

Common faults and causes of compressors

Common faults and causes of compressors Common compressor failures are as follows: 　　L. The compressor cannot start normally 　　 The power supply voltage is too low, the motor circuit is poorly connected, or the exhaust valve is leaking, resulting in too high pressure in the crankcase. The energy regulation mechanism has failed.

06/30/2020

Causes of compressor burnout

Causes of compressor burnout Common failures of compressors are mainly the following three: 1. Motor burned out; 2. Liquid shock; 3. Oil shortage caused by refrigeration oil. 　　 Today I will give you a detailed analysis of the cause of the motor burnout.

06/30/2020

What are the factors that cause motor damage？

What are the factors that cause motor damage？ What are the factors that cause damage to the compressor motor: 　　 1. Abnormal load and stall

Customers frequently viewed

IWAYA DENKI Water Pump 25CJT0752

US$2307.69

Panasonic Servo Motor MHMF022L1V2M

US$653.85

Honeywell Solenoid Valve VE4025B1045

US$334.62

ROTEN Mechanical Seal 8E5K-22-X

US$384.62

KOGANEI Solenoid Valve 110E1-2-J41-83-PSL

US$100.00

NORGREN Air Cylinder RM/92032/M/30

US$207.69

SGO Tool for Metal Cutting Double edged straight knife 1/2x6x20

US$19.87

Rockwell Allen Bradley AB Circuit Breaker 1492-SPM3B630

US$98.38

Copeland Compressor XPV0382E-9E9-581

Toshiba Compressor PH310M2CS-4KTH

US$352.11

Omron Light Curtain F3SJ-A0545N30

US$1685.90

Kompass Vane Pump T6CC-020-006-5R00-C500

BELIMO Butterfly Valve D6450NL

Sanyo Denki Fan 9SG1224P1G06

US$24.28

Related Info

Correct handling method of single compressor

Recent related posts