How to judge the chilled water flow of the chiller
Generally speaking, when buying a chiller, you will have questions. I don't know how to judge the chilled water flow rate of the chiller? From what aspects should the chiller water flow be considered? Today, the editor of okmarts.com will share with you four suggestions:
1. The return water temperature and outlet water temperature detection of the chiller (the unit needs to be in normal state):
After 30 minutes of starting up, check the system or the chilled water system inlet and outlet thermometers through the unit's control system parameters. The inlet and outlet water temperatures of the unit can be read during operation. The difference must be around 4-6 degrees. If the water temperature difference is too large, it means that the water flow through the plate type device in the water system is too small, which may cause the unit to malfunction or be damaged.
2. Water pressure detection of the inlet and outlet pipes of the unit:
Through the detection of the return water pressure and the outlet water pressure value, and then check the water flow rate of the chiller under the pressure difference between the inlet and outlet water in the random manual of the unit, by referring to the water flow corresponding table or diagram of the unit in the manual, In order to judge whether the water system is normal or not; and use this difference to determine which section of the water pipeline has a large resistance value, and make corresponding rectification plans and actions.
3, the compressor copper pipe suction temperature detection (only when the refrigeration is running):
If it is detected that the suction temperature of the compressor is lower than 0 degrees after the refrigeration chiller is turned on for 30 minutes, it means that the water flow in the water-side heat exchanger is not enough, which causes the evaporation temperature and evaporation pressure to drop, and causes the Freon to flow in the evaporator. The suction pipe of the compressor is still evaporating and absorbing heat, which will cause the suction temperature of the compressor to be lower than 0 degrees; in addition, it is necessary to exclude the drop in evaporating pressure and evaporating temperature caused by the too low water temperature set point; The low water temperature unit can be considered normal as long as the compressor has a suction superheat of 6~8℃. Therefore, under normal water flow, the suction temperature of the compressor will generally be greater than 0°C, and water system problems should be eliminated if it is lower than this value.
4. Water pump running current detection:
By detecting the running current of the chiller pump and comparing it with the rated current, it can be judged whether the actual water flow is larger or smaller than the rated water flow of the pump. Only by comprehensively judging with the previous parameters can an accurate water system detection analysis be obtained. Judgment report.
How to judge the chilled water flow of the chiller
Recent related posts
-
08/13/2020
How to judge the chilled water flow of the chiller
Generally speaking, when buying a chiller, you will have questions. I don't know how to judge the chilled water flow rate of the chiller? From what aspects should the chiller water flow be considered? Today, the editor of okmarts.com will share with you fPﰨ2 䀀 湠癐
-
08/13/2020
How to install the cold storage air curtain How much do you know about these technologies
The function and technology of installing the air curtain above the cold storage door, we must first understand why the cold storage needs to install the air curtain. The air curtain prevents the convection of indoor and outdoor air,
-
08/13/2020
How to install large-scale cold storage refrigeration equipment
The cold storage is mainly used as a constant temperature storage air-conditioning equipment for food, dairy products, meat, aquatic products, etc. The cold storage is a kind of low-temperature cold storage and also a kind of refrigeration equipment.
-
08/13/2020
How to deal with the high pressure overload of the chiller
When the condenser heat dissipation is poor, the compressor efficiency is low and the operating current increases. When the high pressure rises to 19Kg/cm2, the compressor trips under the protection of the high pressure switch and the compressor stops runPﰨ2
-
08/13/2020
How to choose the internal machine for cold storage Choose air cooler or exhaust pipe
Most of the cold storages we make are divided into many types, such as high temperature storage, low temperature storage, ultra low temperature storage, etc. So how to choose the internal machine of the cold storage?
-
08/13/2020
How to apply the functions of cooling, heating, humidification, and dehumidification of computer room air conditioning
1. Uninterrupted operation and year-round refrigeration<br></br> The heat dissipation of the equipment in the computer room is a steady-state heat source, and it operates continuously throughout the year. This requires an uninterrupted air-conditioning gPﰨ2 䀀 湠癐
-
08/13/2020
How many of these problems have you encountered with cold storage equipment
The installation of refrigeration system equipment and refrigerant pipelines, even the overall design of the cold storage and the daily use of the cold storage, must be done in strict accordance with the specifications.
-
08/13/2020
How did the sediment in the chiller come from
Water chiller is a kind of water cooling equipment that can provide constant temperature, constant flow and constant pressure cooling water equipment.
-
08/13/2020
Four types of safety protection measures for refrigeration compressors
As the most important component of the chiller, the motor for the refrigeration compressor plays an important role in the after-sales maintenance of the chiller. Moreover, the maintenance cost of the chiller compressor is relatively high.
-
08/13/2020
Decontamination method of cold storage refrigeration pipe
Before installing the cold storage refrigeration pipe, the rust and dirt on the inner and outer walls of the pipe should be thoroughly removed, and the inner wall should be kept dry.
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
TCS Oil Seal TC 18*25*6
FLUKE Battery Li-ion
Shihlin Switch BHL34 4P(50A)