Ice machine installation and commissioning guidelines and installation service process

Ice machine installation and commissioning guidelines and installation service process

Nowadays, whether it is the scorching heat of the summer or the severe winter, the business of the dessert shop is so good that the ice machine naturally works non-stop throughout the year. Today, the editor of okmarts.com will share some tips for installing the newly purchased ice machine with everyone.

　　The ice maker is best installed in a well-ventilated place without direct sunlight.

　　The minimum ventilation distance of the ice machine condenser is at least 1 meter from the front and back of the shelter, and the height is at least 50cm from the roof. It is better to have a larger ventilation distance and keep the air flowing. The installation ground should be kept level, otherwise the machine operation will cause the water storage in the refrigerator to affect the ice quality produced.

After installation, first check the appearance integrity of the machine, whether the ice falling channel is unobstructed, whether the fan blades rotate flexibly, whether all the shut-off valves of the unit are all opened, whether there are oil stains at each welding joint of the unit, and whether the compressor is short of oil. Shuang reminds everyone that oil is closely related to the life of the compressor, and you should always check the oil level and oil color.

　　 Connect the water source and check whether the water pressure is normal. If the water pressure is too low, it will cause the machine to keep alarming. It is recommended to use a water storage tank and a booster pump when the water is stopped frequently. The water level of the inlet tank should be about 10 mm lower than the overflow, and the water level can be adjusted by the float. Also don't forget to check the voltage, the ice machine has its own separate water valve and power supply for easy maintenance in the future.

Do not make ice immediately after the ice maker is powered on. First let the crankcase heater press the oil to heat up, and then let the unit run. Here you should listen to the operating sound of the unit and see how the evaporator freezes. Some ice makers need to add salt water. Yes, it is generally best to add more than 200 grams of salt to a 30kg bucket. At the same time, check whether the water level of the trap is normal.

　　 Recently, some friends have reported that excessive water pressure may cause water to escape from the ice machine while making ice. At this time, you need to close the water valve in front of the water separator.

　　After the unit is operating normally, we have to test some protection functions of the unit.

　　 Water shortage protection. When the machine stops, under normal circumstances, the unit can be stopped by blocking the switch by hand for three minutes. At present, the ice maker stops the press first, and then stops the ice skates after two minutes. This is beneficial to the next start, so that the entire ice bucket is scraped down to facilitate the next start of the ice thickness.

　　After the above steps are completed, the ice machine can operate normally!

　　 An ice machine with good quality and high cost performance must cooperate with a good and standardized installation to make the machine show perfect performance.

　　The steps to install an ice maker are divided into:

　　 1. Site inspection. After the installation master arrives at the site, he needs to consult with the on-site engineering supervisor to confirm the specific location of the ice maker. For air-cooled machines, whether the back and left and right sides meet the manufacturer's requirements for the minimum installation space corresponding to the machine model; whether the power supply, water supply, and drainage used by the ice machine have been installed in place, especially that the drainage needs to be open For structural pipes, the height of the drain pipe opening cannot be higher than the height of the bottom surface of the ice storage bin of the machine.

　　2, check out the box. An ice maker is transported to the installation site by the manufacturer, and there are many links in the middle. Therefore, as an installer, before arriving at the site for installation, you must unpack and check whether the items in the packing list and installation accessories correspond to the factory's packing list, whether there is a shortage, whether there is any damage during the transportation of the machine, and so on.

　　 3. Installation. After checking 1 and 2 there is no problem, start to classify the parts sent by the factory and enter the installation process. When installing the split ice maker, you need to install the four supporting feet of the ice storage bucket first. Make necessary adjustments to the feet according to the installation site conditions. If the height of the machine is not too strict on the site, it is recommended to lengthen the feet of the ice storage bucket, which will help the smooth discharge of the ice melt water at the bottom of the ice storage bucket. Then you need to install the air funnel of the ice bucket. This funnel is the latest patented product of the factory, which can effectively prevent the sewer water from counterattacking into the ice storage bucket if the water channel is blocked, causing the pollution of edible ice. After the ice bucket is installed, install the water inlet copper head and the drain copper head of the host. The water inlet copper head is connected to the purified direct drinking water. After the drain copper head is connected to the drain pipe firmly, the other end is connected to the sewer. . Lift the host on the ice storage bucket, pay attention that the dimensions of the four directions should be consistent with the size of the ice storage bucket, check the level of the machine installation in place, if the machine is not level, you can make the final adjustment through the four supporting feet of the machine to ensure The four supporting feet have been forced to support the machine.

　　 4. Debugging. After the ice storage bucket and the main engine are installed in place, check whether the machine has the conditions for water power and start-up debugging. Pay special attention to whether the main machine's condensing motor fan blades are blocked by foreign objects or blocked. Check thoroughly to make sure that the water inlet valve can be opened after installation, the power switch is turned on, and the ice maker switch is set to the ice making indication position, and the machine enters the automatic ice making mode. Once the machine enters the ice making mode, the installer must observe and record the time, the time between ice making and the ice falling, and the thickness of the ice cubes made. Generally, the thickness of the ice cube has been adjusted in the factory of the ice maker, and there is no need to adjust it during installation, but according to the different needs of individual users for the thickness of the ice cube, adjustment can be made if necessary. Adjust clockwise to make the ice cube thicker, and adjust it counterclockwise to make the ice cube thinner. Each adjustment should not exceed 1/4 turn! Start-up and commissioning should observe the ice making cycle of Sanpanice. The inspection parameters include the filtered water pressure and water temperature; ambient temperature, no-load mains voltage, operating voltage, operating current, ice making cycle time and other main parameters.

　　 5. Training clearance. After completing the record of the various parameters of 4, the installation record form should be completed, and the user should be carefully trained in the daily use and maintenance, and then the user is required to sign the installation record sheet and exit.