Safety code for cold storage wire installation
During the installation of the cold storage, it is very important whether the wires can ensure the safety of later use. For example, explosion-proof cold storage must use explosion-proof wires in the explosion-proof area, so as to ensure the safety of the cold storage during use. The safety of cold storage is more important than Mount Tai.
1. The power cord for cold storage should be a dedicated branch circuit, and its wire capacity should be greater than 1.5 times the maximum operating current value of the refrigeration system z*, so as to ensure safety at the maximum operating current.
2. It is strictly forbidden not to connect the grounding wire or not to connect the grounding wire in the designated position, otherwise it will cause the body shell to become live, and even leakage may occur, which endangers personal safety. The yellow-green wire can only be used as a grounding wire and cannot be used for other purposes.
3. The power cord or control line should be fixed and connected strictly with a crimping card or a wire clamp, otherwise it will cause looseness, sparking, and disconnection, leaving hidden dangers.
4. It is strictly forbidden to use non-standard power cords; all dedicated lines for cold storage should be equipped with air switches or line protection devices such as leakage protection, otherwise it may cause a fire due to the heat of plugs, sockets, wires, etc.; if there is no corresponding air A switch or a leakage protection switch will not prevent short-circuit and leakage accidents caused by equipment failure or accidents, and cannot disconnect the power supply in time, which may easily cause fire and personal injury.
5. It is strictly forbidden to add the power cord or the indoor or outdoor machine connection line when it is not long enough. The entire wire must be replaced, and no joints are allowed in the middle; otherwise it may cause poor contact or generate heat due to the extension part that does not meet the requirements , Sparking fire, causing fire or leakage, endangering personal safety. When the connecting wire is too long, it is strictly prohibited to wind it into a small circle to avoid eddy current heating.
6. It is strictly forbidden to replace the fuse (wire) with copper wire or wire. The fuse (wire) of the same specification should be replaced after the fuse is blown; otherwise, the fuse (wire) will not work, and the circuit board will lose its protection and easily damage the chip. And other components, and even burn out the circuit board.
7. The indoor and outdoor electrical connections of the cold storage should not be affected by tensile and twisting stress; otherwise, it will cause a short circuit or equipment failure or leakage accident caused by the power cord.
8. After the repair is completed, a comprehensive electrical safety inspection of the system must be carried out to eliminate hidden dangers, including whether the wiring terminals or connecting wire connectors are loose, aging, and whether the metal cover is stuck with wires, etc.
The design and construction of cold storage wires should be fully considered in the early stage of cold storage installation, and full consideration should be given to the selection of cold storage wires.
Safety code for cold storage wire installation
Recent related posts
-
08/13/2020
Safety code for cold storage wire installation
During the installation of the cold storage, it is very important whether the wires can ensure the safety of later use. For example, explosion-proof cold storage must use explosion-proof wires in the explosion-proof area
-
08/13/2020
Requirements for adding refrigerant to industrial chiller system
After the industrial chiller system has passed the vacuum test, it can use the vacuum state in the system to charge the refrigerant.<br></br>
-
08/13/2020
Refrigeration system 41 essay questions, too comprehensive!
1. What are the three necessary conditions for the safe operation of the refrigeration system? Answer: (1) The refrigerant pressure in the system must not be abnormally high to avoid equipment rupture.
-
08/13/2020
Reasons for vibration of inlet and outlet pipes of reciprocating compressor
During the air load test of the carbon dioxide compressor, the pipeline between the third-stage outlet buffer and the third-stage cooler, the pipeline between the fourth-stage outlet buffer and the fourth-stage cooler,
-
08/13/2020
Reasons for the reduction of refrigeration equipment system cooling capacity
Refrigeration equipment is a relatively large energy-consuming equipment, especially for summer cooling. Its electricity consumption costs are becoming more and more significant,
-
08/13/2020
Problems that need to be paid attention to when installing chillers
1. Anti-leakage of fluorine<br></br> If the joints of the chiller are not tightened or cracked, fluorine leakage will occur. If the chiller leaks fluorine, the user must replenish it frequently,
-
08/13/2020
Popularization of cold chain technology analysis of the advantages and disadvantages of 5 types of compressors
There are mainly five types of compressors, piston compressors, rolling rotor compressors, turbo compressors, screw compressors, and centrifugal compressors. This article briefly introduces the advantages and disadvantages of various compressors.
-
08/13/2020
New Explanation of Basic Knowledge of Small Chiller System
Small chiller: is a kind of water cooling equipment, small chiller is a kind of cooling water equipment that can provide constant temperature, constant flow and constant pressure.
-
08/13/2020
Maintenance method of chiller cooling tower equipment
We understand that domestic cooling water towers are structures used for cooling water in power plants, and the general height is determined by the size of the power plant units.
-
08/13/2020
Maintenance method of central air conditioning compressor
In the hot summer, people are looking for a comfortable and cool experience. Air conditioner is a must-have summer artifact for every family. Maybe everyone is familiar with only the function and brand price of air conditioner,
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
AirTAC Air Cylinder RMTL25X200
SIEMENS Servo Drive 6SN1112-1AA00-0AA0
DIFU Vane Pump PVD-SF-12C-10
BOURNS Encoder PEC16-2115F-S0012